Bedienungsanleitung Felisatti SDF4.8R (Seite 5 von 28) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

500412

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

DESCRIPTION

1. Collet

2. LED worklight (SDF3.6R)

3. Switch (Forward/Reverse)

4. Stick/Pistol selection button (SDF4.8R)

5. Input jack

6. Charger

7. Charge indicator light

8. To rotate into pistol position (SDF4.8R)

9. To rotate into stick position (SDF4.8R)

APPLICATIONS

You may use this product for driving screw with screw

driver bits.

CHARGING SCREW DRIVER (Fig. 1)

This tool has been shipped in low charge condition to prevent

possible problems. Therefore, you should charge it overnight

prior to use.

Note: Batteries will not reach full charge the  rst time

they are charged. Allow several cycles (driving followed by

recharging) for them to become fully charged.

Note: Only use the charger provided.

■ Connect charger to the tool by inserting charger plug into

input jack. Make sure the power supply is normal household

voltage, 230V, 50Hz, AC only.

■ Connect charger to power supply.

■ The charge indicator light (LED) will light up when charger

is properly connected power supply.

■ After normal usage, a minimum charge time of 3-5 hours is

required to recharge a completely discharged battery.

■ The charger housing and the tool handle will become

slightly warm to the touch while charging.

This is normal and does not indicate a problem.

■ DO NOT operate driver while it is connected to the charger.

The driving ability will not increase.

■ DO NOT place charger in an area of extreme heat of cold.

It works best at normal room temperature.

STICK/PISTOL SELECTION (SDF4.8R)

■ To press selection button at pivot location.

■ Change pistol/stick position by rotating the handle.

ADJUSTING TORQUE (SDF4.8R)

There are twelve torque indicator settings located on the front

of the screwdriver.

■ Rotate adjustment ring to desired setting, aligning num ber

on adjustment ring with arrow on housing.

1 - 2 For driving small screws

3 - 4 For driving screws into soft material

5 - 7 For driving screws into soft and hard materials

8 - 9 For driving screws into hard wood

SWITCH ( FORWARD/REVERSE)

■ To drive for forward motion, depress the upper part of

switch trigger.

■ To drive for reverse motion, depress the lower part of

switch trigger.

LED WORKLIGHT (SDF3.6R)

The screwdriver has a built-in LED worklight. This feature

is convenient when working in close or tight areas where

additional light is needed. Whenever the switch trigger is

depressed, the LED worklight will illuminate.

Note: During normal operation, if the LED worklight will not

illuminate, charge the screwdriver.

The LED worklight will be off during Jam and Stall status.

TECHNICAL DATA

Model SDF4.8R SDF3.6R

Motor Volts DC 4.8 3.6

Collet mm 6.35

No Load Speed r/min (RPM) 200 200

Switch Forward and Reverse

Torque Nm max 3.4 3.5

Weight(Include battery) according EPTA - Procedure

01/2003 Kg

0.6 0.4

Charger electrical characteristics

Input V-AC Hz 220 - 50

Output V-DC mA 6-250 4.8-500

Charge Time hours 5 3

Voltage V 4.8 3.6

Battery capacity Ah 1.1 1.3

Batttery type Ni-Cd Li-ion

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Felisatti SDF4.8R Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info