Bedienungsanleitung Fender BXR 300R (Seite 6 von 7) (Englisch)

470121

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

SUGGESTED FIRST TIME OPERATION

If this the first time you’ve used a FENDER BXR 300 we

suggest that you try the following first time control setting

procedure.

Be sure the speaker is connected with a speaker cable (not an

instrument cable) and the line cord is plugged into a suitable

power source. If you own a BXR 300C, the internal 15 inch

speaker will already be connected.

Depress the two “ENHANCE” buttons and turn the VOLUME

to zero (7 O’CLOCK) and the TREBLE, MID, MID

FREQUENCY, and BASS to “0” (12:00 O’CLOCK), and

DELTACOMP™ off. With your instrument connected, press the

power rocker switch to “ON” The RED PILOT lamp will

illuminate, and the fan in the rear panel will begin to rotate

slowly.

Advance the volume while playing a few notes on the bass.

Experiment with the controls to become familiar with the

features that are available to you.

SETTING UP EXTERNAL SIGNAL PROCESSING

External signal processors may be used as previously

described. Devices used with the preamp out, power amp in

may be set up as follows:

Connect the “PREAMP OUT” to the input jack of the effects

device, and the “POWER AMP IN” to the output jack of the

effects device. Read the owner’s manual for the device as

required. if you get no sound when the device is in the “IN”

mode, you may have the wires to the external device crossed

(exchanged) or the device may not be turned on.

SUGGESTED SPEAKER ARRANGEMENTS

WITH BXR 300R

There are an almost infinite number of speaker setups

possible, what with the variety of speaker systems available.

We will attempt to describe four typical situations.

FIGURE 1

is a common connection favored by the bassist who

wants extremely high level. it should be noted that two 15”

speakers have 50% more cone area than one 18” speaker.

FIGURE 2

is an example of two FENDER BXR 410 ‘s

connected in parallel.

FIGURE

3 shows a BXR 115 and a BXR 410 connected in

parallel, which provides a well balanced wide range

arrangement.

FIGURE 4

illustrates one FENDER BXR SPECTRUM system

operating in full range mode. With it’s 18” woofer, the

SPECTRUM is ideal for five string bass.

PARALLEL SPEAKERS

When speakers are connected in parallel, as in the example

FIGURE 1, 2, and

3 above, the impedance of two equal

systems will halve. impedance of equal impedance systems

will have a new impedance equal to the individual identical

impedance divided by the number of systems. The minimum

for the FENDER BXR 300 is 4 ohms, there is no maximum (if

no speakers are connected, no harm will result).

MECHANICAL OPTIONS

For those users who will not be “rack mounting” their BXR

300R we have provided the option of removable rack ears.

with the rack ears removed, an optional strap handle kit may

be installed. If you should use a handle kit other than

FENDER, be sure that the mounting screws protrude no more

than 1/2 inch past the mounting plane (underside) of the

handle.

If you decide at a later time to re-install the rack ears, make

sure that you use the same screws that were originally

supplied.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fender BXR 300R Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info