Bedienungsanleitung Fender KXR 200 (Seite 3 von 7) (Englisch)

607105

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

CHANNEL 1 INPUT (1/4 INCH) - Plug-in connector for

instruments. This balanced input can handle as much

as 8V R.M.S.

CHANNEL 1 VOLUME CONTROL - This control adjusts

the preamplifier gain of channel 1. It works in con-

junction with the Master Volume control ( item I) to set

the overall loudness of the amplifier for channel 1

only. Being a true “gain” control, it allows for the use

of a variety of microphones, keyboards or other instru-

ments with differing output signal levels. Low-level

instruments generally require a higher Channel

Volume setting while “hotter” keyboards will require a

lower setting.

CHANNEL 1 EQUALIZER - This equalizer allows

adjustments of the tonal characteristics of channel 1

before amplification. Each control provides a 12dB

boost or cut to bands of frequencies centered about

130, 540, and 4200 Hz. Note that all equalizer sec-

tions of the KXR 200 are designed so that if all center

frequencies are set at +12dB, a flat overall response

would be obtained. This is very useful if the signal

source is weak.

CHANNEL 1 EFFECTS SEND CONTROL - This control

works in conjunction with the effects send jack (item R),

effects return jack (item S), and the effect return con-

trol (item J) to , respectively, allow a desired amount of

preamp signal to be massaged, and to control the

amount of return signal that has gone through an

external effects device. The effects send control in con-

junction with the effects send jack could be used to

drive another KXR 200 as a slave amp. This is done

by connecting the effects send jack, with a standard

guitar cord, to the effects return jack of another KXR

200. Note that each channel could be set to send a

different amount of signal to the effects bus.

CHANNEL 1 REVERB SEND CONTROL - This control

works in conjunction with the reverb return control

(item K) to allow the amount of reverb to be mixed

with the dry signal. The amount of reverb-sent signal

is independent for each channel.

CHANNEL 2 AND 3 - These two channels are provid-

ed for two additional instruments. All the controls and

jacks operate in the same manner as those in channel

1. When not in use, it is best to turn the channel vol-

ume, the effects send and the reverb send controls all

the way down to avoid any amplification of unwanted

noise. Likewise, when not in use, the equalizer sec-

tions should be kept flat ( i.e. all knobs should be set at

12 O’clock).

CHANNEL 4 - This channel operates in the same man-

ner as the other three channels, but with the addition

of a few extra features: The XLR jack and an extra

band in the equalizer section. With the vocalist in

mind, the balanced, low impedance XLR jack provides

a suitable connection for a microphone. Furthermore,

the four-band equalizer was designed around the

F,G.

CHANNEL 3

VOLUME

010

HIGHMIDLOW

-12 +12

REVERBEFFECTS

010

SEND

VOLUME

010

LOW

-12 +

CHANNEL 1

VOLUME

010

HIGHMIDLOW

-12 +12

REVERBEFFECTS

010

SEND

CHANNEL

VOLUME

010

MIDLOW

-12 + 12

INPUT

INPUT MIC

KXR 200 FRONT PANEL FUNCTIONS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fender KXR 200 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info