Bedienungsanleitung Fender RR 263 (Seite 3 von 4) (Englisch)

442894

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

NOTE: BEFORE ATTEMPTING TO OPERATE YOUR

‘63 FENDER REVERB

, turn the unit around and look

inside the back. You will see a metal lever near the back and

slightly left of center. This lever, when in the shipping or

traveling position, is pushed toward the front of the cabinet

and then to the right to lock. This lever pushes the inside of

the pan against a soft foam pad and prevents the springs in

the pan from being damaged due to excessive movement. To

release the lever to the playing position, push the lever

slightly forward and then to the left to unlock it. Let the lever

come back as for as it can to release the pan.

‘63 Fender Reverb top panel functions

A. POWER SWITCH-Turns the AC power ON and OFF.

When the switch is in the OFF position, the unit is

completely shut down.

B. FUSE-The fuse is in the AC supply of the amplifier and

will help to protect the amplifier and the operator in the

event of an electrical fault. If a fuse blows, it should only

be replaced with a fuse in accordance with the listing at

the fuse holder. If an amplifier repeatedly blows fuses, it

should be checked out by a qualified technician. UNDER

NO CIRCUMSTANCES should a fuse of a different type,

higher current rating, or a fuse bypass be used, as this

could damage the equipment and present a serious safety

hazard.

C. PILOT LIGHT-This lamp is illuminated when the

power is on.

D. DWELL-Adjusts the amount of signal sent to the reverb

pan. At low Dwell settings (two to four) the reverb sounds

much like a guitar played into a large room. At high

Dwell settings (above four) the reverb signal will start to

sound more “springy” or ‘twangy”.

E. INPUT-A high impedance plug-in connection for

instruments.

F. MIXER-The reverb “wet” signal and the ‘dry” signal are

mixed together at this control. The mixer adjusts what

percentage of the signal sent to the output jack is from the

reverb pan circuit compared to the dry signal. Higher

settings equal more reverb.

G. TONE-This control affects only the “wet’ portion of the

signal and acts much like the treble control on a guitar

amplifier. Turning the Tone control up allows more high

frequencies through from the reverb to the mixer control.

H. OUTPUT-This is the output jack that is used to send the

signal from the reverb unit to the amplifier.

Using your ‘63 Fender Reverb

The ‘63 Fender Reverb is designed to go between a low level

instrument (such as a guitar) and a high input impedance

amplifier (such as any Fender tube amplifier or the high

sensitivity input on any Fender solid-state amplifier). It

should be used only with the clean channel of the

amplifier as distorted reverb sounds very unnatural. If

you want to use the ‘63 Fender Reverb with high gain or

distortion, you may use either a distortion pedal inserted

before the Reverb Unit or connect the Reverb Unit in the

effects loop of the amplifier and use the high

gain/distortion channel of the amplifier. However, since

most of the sonic benefits of the ‘63 Fender Reverb result

from the fact that the reverb signal is generated before

the tone controls and preamp gain circuitry of the

amplifier, we do not recommend using it in the effects

loop.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fender RR 263 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info