Bedienungsanleitung Fender Tone Master (Seite 5 von 7) (Englisch)

443064

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

TONE MASTER REAR PANEL FUNCTIONS

A. FUSE - The fuse is in the AC supply of the amplifier and will help to protect the amplifier in the

event of an electrical fault or tube failure. If a fuse blows, it should only be replaced by one with

the same type and rating. NEVER use a fuse of higher current rating as this could damage the

equipment and present a serious safety hazard. If the amplifier repeatedly blows fuses, it should

be checked out by an authorized Fender service center.

B. POWER SWITCH - This switch turns the AC power on and off. When this switch is OFF the

amplifier is completely shut down.

C. STANDBY SWITCH - This turns the amplifier on and off. In the STANDBY position, the ampli-

fier is off, although power is applied to the tube filaments to keep them warmed up and ready to

play. A good rule of thumb is to turn the power switch on and wait at least 50 seconds before

turning on the standby switch. Using this switch during short breaks will increase tube life.

D. IMPEDANCE SWITCH - This is labeled LO, MED and HI. This switch serves two functions.

One, to set the output impedance of the amplifier to best match the speaker impedance for max-

imum power. Second, to enable the amplifier to better achieve the cranked-up sound at a lower

volume. On the B CHANNEL, with a single Tone-Master enclosure, this switch should be set

according to the setting of the B CHANNEL volume knob: For volume settings of 3.5 and lower,

LO would be the appropriate setting. For settings of 3.5 to 7, MED is best. For settings above 7,

HI will produce full power and tone. This switch will not damage tubes or reduce tube life at

these settings. What it does do is increase the gain in the LO and MED settings and thereby bet-

ter approximate the Full volume sound at a lower level than by adjusting the VOLUME alone.

With a single 16Ω enclosure, LO will produce 30 watts, MED will Produce 60 watts, and HI will

produce a full 100 watts. With two 16Ω enclosures, (an 8Ω load), LO will produce 60 watts, and

MED will Produce 100 watts. In the A CHANNEL, the switch has the same function, although

blues players may like running the switch on LO all the time to get that great crying tone.

Conversely, a player looking for a New Wave Strat

tone might like the sound of the A CHANNEL

on HI.

E. SPEAKER - Plug in connection for speakers. This jack must be used as the primary connection

for speakers.

IMPEDANCE Ω

MED HILO

CAUTION:

RISK OF ELECTRIC SHOCK

DO NOT OPEN

360W

AVIS:

RISQUE DE CHOC

ELECTRIQUE NE PAS OUVRIR

ATTENTION:

UTILISER UN FUSIBLE DE

RECHANGE DE MEME

TYPE ET CALIBRE

CAUTION:

TO REDUCE THE RISK OF

FIRE, REPLACE FUSE WITH

SAME TYPE AND RATING

T4A

250V

FUSE

CAUTION: CHASSIS SURFACE HOT

WARNING: TO REDUCE THE RISK

OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS EQUIPMENT TO

RAIN OR MOISTURE

ATTENTION:

SUPERFICIE DE CHASSIS

CHAUDE

PARALLEL

SPEAKER JACKS

100W

4Ω min. TOTAL

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fender Tone Master Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info