763616
4
Zoom out
Zoom in
Vorherige Seite
1/22
Nächste Seite
Ferm 41
Using extension cables
Only use an approved extension cable suitable for the
power input of the machine. The minimum conductor
size is 1.5 mm2. When using a cable reel always unwind
the reel completely.
Check that the maximum speed indicated on the
grinding disc corresponds to the maximum speed of
the machine. The speed of the machine must not
exceed the value on the grinding disc.
Make sure that the dimensions of the grinding disc
correspond to the specifications of the machine.
Make sure that the grinding disc has been mounted
and fastened properly. Do not use reducing rings or
adapters to make the grinding disc fit properly.
Treat and store grinding discs in conformance with
the supplier’s instructions.
Do not use the machine for grinding workpieces with
a maximum thickness exceeding the maximum
grinding depth of the grinding disc.
Do not use grinding discs for deburring.
When grinding discs have to be mounted on the
thread of the spindle, make sure that the spindle has
sufficient thread. Make sure that the spindle is
sufficiently protected and does not touch the
grinding surface.
Before use, inspect the grinding disc for any damage.
Do not use grinding discs which are crack-ed, ripped
or otherwise damaged.
Before use, let the machine run idle for 30 seconds.
Immediately switch off the machine in case of
abnormal vibrations or occurrence of another
defect. Carefully inspect the machine and grinding
disc before switching the machine on again.
Make sure that sparks do not put people into danger
or that they contact highly flammable substances.
Make sure that the workpiece is sufficiently
supported or clamped. Keep your hands away from
the surface to be cut.
Always wear safety goggles and hearing protection. If
desired or required also use another kind of
protection like for example an apron or helmet.
Ensure that mounted wheels and points are fitted in
accordance with the manufacturer’s instructions.
Ensure that blotters are used when they are
provided with the bonded abrasive product and
when they are required.
If a guard is supplied with the tool never use the tool
without such a guard.
For tools intended to be fitted with threaded hole
wheel, ensure that the thread in the wheel is long
enough to accept the spindle length.
Ensure that ventilation openings are kept clear when
working in dusty conditions. If it should become
nessesary to clear dust, first disconnect the tool
from the mains supply (use non metallic objects) and
avoid damaging internal parts.
Though poor conditions of the electrical mains,
shortly voltage drops can appear when starting the
equipment. This can influence other equipment (eq.
blinking of a lamp). If the mains-impedance Zmax
<0.348 Ohm, such disturbances are not expected.
(In case of need, you may contact your local supply
authority for further information.
3. ASSEMBLY
Prior to mounting an accessory always unplug
the tool.
MOUNTING A GRINDING DISC.
Fig 2
Use grinding discs of the correct dimension. Use fibre
reinforced grinding discs only. The grinding disc must
not touch the edge of the guard.
Press the spindle lock (6) and turn the spindle (9)
until it engages in the lock. Keep the spindle lock
pressed during this procedure.
Remove the flange nut (12) from the spindle using the
spanner (11).
Position the grinding disc (7) on the flange (5).
Place the flange nut on the spindle an tighten it using
the spanner.
Release the spindle lock and check that the spindle is
unlocked by rotating it.
MOUNTING THE SIDE HANDLE
Fig 1
The side handle can be used for both left-hand and right-
hand control.
Fasten the side handle (Fig. 5) for left-hand operation
on the right-hand side of the machine.
Fasten the side handle for right-hand operation on
the left-hand side of the machine.
Fasten the side handle for upright working at the top
of the machine.
Make sure that the side handle is fastened
properly and cannot loosen unexpectedly.
MOUNTING GRINDING DISCS AND
ROUGHING DISCS
Fig. 3 and 4 show how to mount the flange (10) when
using thick (4 – 8 mm) and thin (2,5 – 4 mm) discs.
4. USE
SPECIAL ATTENTION WHEN STARTING
THE MACHINE
Clamp the workpiece and make sure that the
workpiece cannot slide from under the machine
during the cutting activities.
When working with the machine, always hold it firmly
with both hands and provide for a secure stance.
Always direct the cable to the rear away from the
machine.
Insert the mains plug only when the machine is
switched off.
Apply the machine to the workpiece only when
switched on
Never use the machine for grinding magnesium
workpieces.
SWITCHING ON AND OFF
This machine is equipped with a safety switch.
Start the machine by pressing the “lock off” button
(to disengrage the switch) and switch on the
machine.
4Ferm
4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Ferm AGM1026 - FAG-230-2000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info