Bedienungsanleitung Ferm agm1029 (Seite 7 von 136) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Norwegisch)

390340

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

following wiring instructions are followed.

The wires in the mains cable are coloured in

accordance with the following code:

blue neutral

brown live

As the colours of the wires in the mains cable of

the unit may not correspond to the coloured

markings identifying the terminals in the plug,

proceed as follows:

- The wire which is coloured blue must be

connected to the terminal which is marked with

the letter N or coloured black.

- The wire which is coloured brown must be

connected to the terminal which is marked with

the letter L or coloured red.

TECHNICAL DATA

AGM1029

Mains voltage V~ 230

Mains frequency Hz 50

Power input W 2,000

No-load speed min

-1

6,000

Grinding disc

Diameter mm 230

Bore mm 22

Spindle thread M14

Weight kg 5.7

NOISE AND VIBRATION

AGM1029

Sound pressure (L

) dB(A) 94.5

Acoustic power (L

) dB(A) 107.5

Uncertainty (K) dB(A) 3

Vibration m/s

6.63

Uncertainty (K) m/s

1.5

Vibration level

The vibration emission level stated in this

instruction manual has been measured in

accordance with a standardised test given in EN

60745; it may be used to compare one tool with

another and as a preliminary assessment of

exposure to vibration when using the tool for the

applications mentioned

- using the tool for different applications, or with

different or poorly maintainted accessories, may

signicantly increase the exposure level

- the times when the tool is switched off or when it

is running but not actually doing the job, may

signi cantly reduce the exposure level

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work

patterns

Wear hearing protection.

DESCRIPTION (FIG. A)

Your angle grinder has been designed for grinding

and cutting masonry and steel.

1. On/off switch

2. Lock-off button

3. Spindle lock button

4. Spindle

5. Guard

6. Main grip

7. Auxiliary grip

8. Release button for main grip

9. Carbon brush holder

ASSEMBLY

Before assembly, always switch off the

machine and remove the mains plug

from the mains.



Do not use the machine without the

guard.

Mounting

● Place the machine on a table with the spindle

(4) facing upwards.

● Keep the spindle lock button (3) pressed and

remove the ange (10) using the ange key (11).

● If necessary, remove the grinding disc (12).

● Remove the ange (13).

● Mount the guard (5). Secure the guard (5) by

tightening the Allen screw (14) and the nut (15)

with the Allen key (16).

● Mount the ange (13).

● If necessary, mount the grinding disc (12).

● Keep the spindle lock button (3) pressed and

mount the ange (10) using the ange key (11).

Removing

● Place the machine on a table with the spindle

(4) facing upwards.

● Keep the spindle lock button (3) pressed and

remove the ange (10) using the ange key (11).

● If necessary, remove the grinding disc (12).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm agm1029 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info