Bedienungsanleitung Ferm AGM1042 (Seite 7 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

510099

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite



Ifthemoulded3-pinplugattachedtotheunitis

damaged and needs replacing, it is important that

it is correctly destroyed and replaced by an

approvedBS1363/5Afusedplugandthatthe

following wiring instructions are followed.

The wires in the mains cable are coloured in

accordance with the following code:

blue neutral

brown live

As the colours of the wires in the mains cable of

the unit may not correspond to the coloured

markings identifying the terminals in the plug,

proceed as follows:

- The wire which is coloured blue must be

connected to the terminal which is marked with

the letter N or coloured black.

- The wire which is coloured brown must be

connected to the terminal which is marked with

theletterLorcolouredred.

TECHNICAL DATA

AGM1042

Mainsvoltage V~ 230

Mainsfrequency Hz 50

Power input W 750

No-load speed min

-1

11,000

Grinding disc

 Diameter mm 115

Bore mm 22.2

Spindlethread  M14

Weight kg 2.2

NOISE AND VIBRATION

AGM1042

Soundpressure(L

) dB(A) 87.7

Acousticpower(L

) dB(A) 98.7

Uncertainty(K) dB(A) 3

Vibration m/s

7.52

Uncertainty(K) m/s

1.5

Wear hearing protection.

Vibration level

The vibration emission level stated in this instruction

manual has been measured in accordance with a

standardisedtestgiveninEN60745;itmaybeused

to compare one tool with another and as a

preliminary assessment of exposure to vibration

when using the tool for the applications mentioned

- using the tool for different applications, or with

different or poorly maintainted accessories,

maysignicantlyincreasetheexposurelevel

- the times when the tool is switched off or when

it is running but not actually doing the job, may

signicantlyreducetheexposurelevel

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

yourhandswarm,andorganizingyourwork

patterns



Your angle grinder has been designed for grinding

and cutting masonry and steel.

 1. On/offswitch

 2. On/offswitchlock

 3. Spindlelockbutton

 4. Spindle

5. Guard

 6. Maingrip

7. Auxiliary grip

8. Carbon brush indicator

ASSEMBLY

Before assembly, always switch off the

machine and remove the mains plug

from the mains.

Mounting and removing the grinding disc



Never attempt to remove the guard.

Mounting

● Placethemachineonatablewiththeguard

(5) facing upwards.

● Mountthespacer(9)ontothespindle(4).

● Mountthegrindingdisc(10)ontothespindle(4).

● Keepthespindlelockbutton(3)pressedand

rmlytightenthetensionnut(11)usingthe

spanner (12).

Removing

● Placethemachineonatablewiththeguard

(5) facing upwards.

● Keepthespindlelockbutton(3)pressedand

loosen the tension nut (11) using the spanner

(12).

● Removethegrindingdisc(10)fromthespindle

(4).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm AGM1042 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info