Bedienungsanleitung Ferm AGM1062S (Seite 8 von 176) (Alle Sprachen)

763249

Zoom out

Zoom in

Vorherige Seite

1/176

Nächste Seite

c) When wheel is binding or when interrupting

a cut for any reason, switch off the power

tool and hold the power tool motionless

until the wheel comes to a complete stop.

Never attempt to remove the cut-off wheel

from the cut while the wheel is in motion

otherwise kickback may occur. Investigate

and take corrective action to eliminate the

cause of wheel binding.

d) Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed

and carefully re-enter the cut. The wheel

may bind, walk up or kickback if the power tool

is restarted in the workpiece.

e) Support panels or any oversized workpiece

to minimize the risk of wheel pinching and

kickback. Large workpieces tend to sag under

their own weight. Supports must be placed

under the workpiece near the line of cut and

near the edge of the workpiece on both sides

of the wheel.

f) Use extra caution when making a “pocket

cut” into existing walls or other blind areas.

The protruding wheel may cut gas or water

pipes, electrical wiring or objects that can

cause kickback.

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Always check that the voltage of the

power supply corresponds to the voltage

on the rating plate label.

Class II machine - Double insulation - You

don’t need any earthed plug.

If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk

of electric shock.

2. MACHINE INFORMATION

Intended use

Your angle grinder has been designed for grinding

masonry and steel materials without the use of

water. For cutting, a special protection guard

must be used (not included) Fig. D2.

Technical specifications

Model No AGM1062S

Mains voltage 230-240 V~

Mains frequency 50 Hz

Power input 1100W

Rated speed 12.000 /min

Wheel disc for grinding

Diameter 125 mm

Bore 22.2 mm

Thickness 6 mm

Wheel disc for cutting

Diameter 125 mm

Bore 22.2 mm

Thickness 3 mm

Spindle thread M14

Weight 2.14 kg

Sound pressure (LPA)87.97 + 3 dB(A)

Acoustic power (LWA)98.97 + 3 dB(A)

Vibration “Surface grinding” ah,AG 15.161 + 1.5 m/s2

Vibration level

The vibration emission level stated in this

instruction manual has been measured in

accordance with a standardised test given in

EN 60745; it may be used to compare one tool

with another and as a preliminary assessment of

exposure to vibration when using the tool for the

applications mentioned

 

different or poorly maintained accessories,

may significantly increase the exposure level

 

it is running but not actually doing the job, may

significantly reduce the exposure level.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm AGM1062S Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info