Bedienungsanleitung Ferm AGM1096P (Seite 8 von 160) (Alle Sprachen)

763256

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

Fig. A

1. Spindle lock button

2. Allen screw

3. Protection guard

5. On/Off switch

6. Side handle connection point

7. Side handle

Fig. B

8. Spindle

9. Mounting flange

10. Wheel disc (not included)

11. Clamping nut

12. Spanner

Fig. C1 & C2

Protection guard for grinding

Assembly

Before assembly, always switch off the

machine and remove the mains plug from

the mains.

Assembling the protection guard (Fig. C)

• Place the machine on a tablewith the spindle

(8) facing upwards.

• Place the protection guard (3) over the

machine head as shown in Fig. C making sure

the ridges on the protection guard fall into the

notches of the machine head.

• Turn the protection guard counter clockwise and

secure the guard by tightening the screw (14).

Never attempt to remove the guard.

Mounting and removing the disc (Fig. B)

• Always use suitable wheel disc for this

machine with diameter Ø 125mm and a bore

from 22.2 mm the thickness of the wheel disc

should be 6 mm for wheel disc for grinding and

3 mm for wheel disc for cutting, the mounting

wheel disc may not touch the safety guard.

Mounting

• Place the machine on a table with the

protection guard (3) facing upwards.

• Mount the flange (9) onto the spindle (8).

• Place the wheel disc (10) onto the spindle (8).

• Keep the spindle lock button (1) pressed and

firmly tighten the clamping nut (11) onto the

spindle (8) by using the spanner (12).

Removing

• Place the machine on a table with the

protection guard (3) facing upwards.

• Keep the spindle lock button (1) pressed and

loosen the clamping nut (11) using the spanner

(12).

• Remove the wheel disc (10) from the spindle (8).

• Keep the spindle lock button (1) pressed and

firmly tighten the clamping nut (11) using the

spanner (12).

Mounting the side handle (Fig. A and B)

• The side handle (7) can be screwed into one of

the three side handle connection point (6).

3. OPERATING

Make sure that the work piece is properly

supported or fixed and keep the supply

cord routing away from the work area.

Switching on and off (Fig. A)

• To switch the machine on, keep the lock-off

button (17) pressed and then press the On/off

switch (5).

• To switch the machine off, release the On/off

switch (5).

Hold the machine away from the work piece when

turning it on and off because the wheel disc could

damage the work piece.

• Clamp the work piece firmly or use another

method to ensure that it cannot move while

working.

• Check the discs regularly. Worn wheel discs

have a negative effect on the machine’s

efficiency. Change to a new wheel disc in good

time.

• Always first turn the machine off after use

before removing the plug from the socket.

Deburring (Fig. E)

An angle of inclination of 30º to 40º will give the

best results when deburring. Move the machine

back and forth using light pressure. This will

prevent the work piece from discolouring or

becoming too hot and will avoid making groves.

Never use abrasive cutting discs for

deburring work!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm AGM1096P Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info