Bedienungsanleitung Ferm AGM1097P (Seite 10 von 182) (Alle Sprachen)

763257

Zoom out

Zoom in

Vorherige Seite

1/182

Nächste Seite

3. OPERATING

Make sure that the work piece is properly

supported or fixed and keep the supply

cord routing away from the work area.

Switching on and off (Fig. A)

• To switch the machine on, push the switch

forward and press the On/off switch (5).

• To switch the machine off, release the On/off

switch (5).

Hold the machine away from the work piece when

turning it on and off because the wheel disc could

damage the work piece.

• Clamp the work piece firmly or use another

method to ensure that it cannot move while

working.

• Check the discs regularly. Worn wheel discs

have a negative effect on the machine’s

efficiency. Change to a new wheel disc in good

time.

• Always first turn the machine off after use

before removing the plug from the socket.

Deburring (Fig. E)

An angle of inclination of 30º to 40º will give the

best results when deburring. Move the machine

back and forth using light pressure. This will

prevent the work piece from discolouring or

becoming too hot and will avoid making groves.

Never use abrasive cutting discs for

deburring work!

Cutting (Fig. F)

For cutting, a special closed protection guard (Fig.

D2) must be used (not included).

Maintain firm contact with the work piece to

prevent vibration and do not tilt or apply pressure

and when cutting. Use moderate pressure when

working, appropriate to the material that is

being worked on. Do not slow down wheel discs

by applying sideways counter pressure. The

direction in which you want to cut is important.

The machine must always work against the

direction of the cut; so never move the machine

in the other direction! There is the risk that the

machine will catch in the cut causing kickback

and that you will lose control.

Hints for optimum use

• Clamp the work piece. Use a clamping device

for small work pieces.

• Hold the machine with both hands.

• Switch on the machine.

• Wait until the machine has reached full speed.

• Place the wheel disc on the work piece.

• Slowly move the machine along the work

piece, firmly pressing the wheel disc against

the work piece.

• Do not apply too much pressure on the

machine. Let the machine do the work.

• Switch off the machine and wait for the

machine to come to a complete standstill

before putting the machine down.

4. MAINTENANCE

Before cleaning and maintenance, always

switch off the machine and remove the

mains plug from the mains.

Clean the machine casings regularly with a soft

cloth, preferably after each use. Make sure that

the ventilation openings are free of dust and

dirt. Remove very persistent dirt using a soft

cloth moistened with soapsuds. Do not use any

solvents such as gasoline, alcohol, ammonia,

etc. Chemicals such as these will damage the

synthetic components.

Replace power cords

If the supply cord is damaged, it must be replaced

by the manufacturer, its service agent or similarly

qualified persons in order to avoid a hazard.

Mains plug replacement (UK only)

If the moulded 3-pin plug attached to the unit is

damaged and needs replacing, it is important

that it is correctly destroyed and replaced by

an approved BS 1363/13A fused plug and that

the following wiring instructions are followed.

The wires in the mains cable are coloured in

accordance with the following code:

• blue neutral

• brown live

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm AGM1097P Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info