Bedienungsanleitung Ferm ATM1043 (Seite 5 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

763847

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Wear ear and eye protection



• Avoid too high pressure

• Keep bystanders and pets away

• Children and animals should be kept far away

from the area of operation of the machine.

• If the compressor is no longer in use, always

take the plug out of the plug socket.

• Always make sure that compressed-air hoses

are used for compressed air and which are

characterized by a maximum pressure

adjusted to that of the compressor. Do not try

to repair the hose if it is damaged.



• Preferably wear safety glasses.

• Do not use the tool in a work area where

stairs, ladders or scaffolding are involved.

• Use accessories with adequate speed rating.

• Never aim the air flow at people or animals.

• Be cautious when using compressed air.

• Only use clean and dry compressed air as a

power source for the tool. Never use oxygen

or a combustible gas.

• Do not exceed maximum operating pressure.

• Keep the tool clean. Do not use any

aggressive or alcohol-based cleaner.

• Never use gasoline or other flammable liquids

to clean the tool. Vapours in the tool will ignite

by a spark and cause the tool to explode.

• Disconnect the tool from the air supply before

troubleshooting or servicing, or during non-

operation.

• Only carry the tool at the grip and never with

the trigger actuated.

• Never carry the tool by the air hose or pull the

air hose to move the tool.





Fig. B

• Wrap a piece of sealing tape around the

connecting piece (7) of the air hose.

• Fit the connecting piece of the air hose into

the connection (3).

• Check whether the air hose is connected

properly.



Fig. C & D

• Fit a socket onto the accessory holder (4).

• Firmly press the socket onto the accessory

holder.



Fig. E & F

• Turn the adjusting knob (2) counterclockwise

to increase the impact force.

• Turn the adjusting knob clockwise to reduce

the impact force.

1 - 190 Nm

2 - 220 Nm

3 - 260 Nm

4 - 310 Nm



Fig. A

• Push the forward/reverse switch (6) forward

for clockwise rotation.

• Push the forward/reverse switch backward for

counterclockwise rotation.

• Tighten the screw.





• Check whether the trigger can move freely.

• Make sure that the tool is lubricated before

connecting it to compressed air.

• Check if the air hose is correctly fitted.

• Set the air pressure to a value within the

allowable operating pressure.

• Only keep your finger on the trigger at the

moment of starting the tool.



• To switch on the tool, press the trigger switch (1).

• To switch off the tool, release the trigger

switch.



Fig. A, C & D

• Fit a required socket.

• Select the direction of rotation.

• Place the tool on the fastener.

• Switch on the tool.

• If necessary, adjust the impact force.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm ATM1043 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info