Bedienungsanleitung Ferm BCM1020 (Seite 7 von 132) (Alle Sprachen)

762278

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

Jump starting

WARNING! Always make all the

connections as described in the correct

order. The vehicle’s electronics may

otherwise be damaged. Proceed against

the specifications at your own risk and

responsibility.

Attention: This function is not suitable for

batteries below 45 Ah. This function could

damage batteries below 45 Ah.

Diesel vehicles and large-volume engines in part

require amperages above 75 A for jump starting.

Note: The charger features an analysis program to

protect the battery from damage (e.g. sulphation

or rapid voltage drops), particularly during jump

starting. The device will not switch on the jump

starter with severely drained or heavily stressed

batteries to protect the battery. During this

process the battery is already being charged with

lower currents (Charging lights up). The display

continues to read “0“. In this event the jump start

function cannot be used. This will protect the

battery from damage. You should then first charge

the battery. You may also use the “Fast charge” or

“Normal charge” function for this purpose.

• Connect the car charger’s mains cable (9) to

power.

• Connect the red connector clamp ( 7) to the

positive battery terminal. (The positive terminal

is marked with a “+“ symbol and a black mark.)

• Connect the black connector clamp ( 6to

the negative battery terminal. (The negative

terminal is marked with a “-“ symbol and a

black mark.)

• If the connector clamps are connected

correctly, the car charger will automatically

select the correct battery type. You may

review it in the “Battery Type“ option field and

if necessary change it by pressing the battery

type button (2) .

• Now select the “Start“ function using the

Charge Start button 3 . The cart charger will

now analyses the battery‘s charge level. The

display will now read “0“.

• Start the vehicle‘s ignition. The display will

now show a 5 second countdown (of which

2 second priming / analysis function and 3

second jump start function at 75 A) when

needing the car charger for jump starting

(previously analyzed by the car charger).

During this countdown the car charger will

briefly deliver 75 A to bridge the battery to

start the car. This is followed by a 180 second

pause to protect the battery. The cycle will now

restart (2 second priming / analysis function

and 3 second jump starting at 75 A / 180

second pause).

• To disconnect the device, first remove the

terminal clamps ( (6) / (7) ) and unplug the

power cord (9) .

Note: If the battery is completely drained, the 75A

will not be sufficient to start all engines (e.g. diesel

vehicles).

- In this case, please select “Fast Charge”

option using the charge start button (3) and

charge the battery 60% (preheating of diesel

engines draws power from the battery. This

requires 60% after preheating).

You can monitor the charging process in the

display by selecting the “Battery%” option using

the digital display button (1).

- Once 60% has been reached, jump start

again.

Attention: Exit the mode by unplugging the mains

cable (9).

4. MAINTENANCE

Always remove the plug from the mains socket

when the battery charger is being serviced or

cleaned. Never use any water or other liquids

when cleaning the charger. Keep the cable and

your battery charger clean. Some cleaners and

solvents (petrol, thinner) can affect or dissolve

plastic parts. These products contain a.o.

benzene, trichloroethylene, chloride and ammonia.

CAUTION! To avoid electrical danger, the

charger should be connected to a mains

supply with good earthing and may not

be subjected to rain or snow. Any

damaged cables must be immediately

replaced by a qualified specialist.

Replace the fuse

The car charger fuse can be damaged by e.g.

hardware failure, overload, ect.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm BCM1020 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info