Bedienungsanleitung Ferm BCM1022 (Seite 13 von 24) (Englisch)

763649

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Trimmer head usage

Always wear eye protection such as

safety goggles. Never lean over the

rotating cutting head. Rocks or other

debris could be thrown into eyes and

face and cause serious personal injury.

Keep the debris guard attached in place

at all times when the unit is operated.

Trimming grass and weeds

Fig. 17

Always remember that the TIP of the line does

cutting. You will achieve better results by not

crowding the line into the cutting area. Allow the

unit to trim at its own pace.

1. Hold the unit so the head is off the ground and

is tilted about 20 degrees toward the sweep

direction.

2. You can avoid thrown debris by sweeping from

your right to the left.

3. Use a slow, deliberate action to cut heavy

growth. The rate of cutting motion will depend

on the material being cut. Heavy growth will

require slower action than will light growth.

4. Never swing the unit so hard as you are in

danger of losing your balance or control of the

unit.

5. Try to control the cutting motion with the hip

rather than placing the full workload on the

arm and hands.

6. Take precautions to avoid wire, grass and

dead, dry, long-stem weeds from wrapping

around the head shaft. Such materials can stall

the head and cause the clutch to slip, resulting

in damage to the clutch system if repeated

frequently.

Adjusting the line length

• Your brush cutters is equipped with a semi-

auto type nylon line head that allows the

operator to advance the line without stopping

the engine. When the line becomes short,

lightly tap the head on the ground while

running the engine at full throttle.

• Each time the head is bumped, the line

advance about 1 inch (25.4 mm). For better

effect, tap the head on bear ground or hard

soil. Avoid bumping in thick, tall grass as the

engine may stall by overload.

Metal blade usage

Fig. 18

When sharpening, removing, or

reattaching the blade, be sure to wear

thick, sturdy gloves and use only proper

tools and equipment to prevent injury.

Choose a suitable recommended cutting

attachment according to the object to be cut.

1. Check the bolt to fasten the blade and be sure

the bolt has no fault, and no abrasion.

2. Be sure that the blade and the holder have been

fastened according to instruction and the blade

turns smoothly without abnormal noise.

3. By using the harness, hang the unit on your

right side. Adjust the harness length so that the

cutting head may become parallel to the ground.

Make sure to use harness and cutting

attachment guard. If not, it is very

dangerous when you slip or lose your

balance.

The rotating parts fastened incorrectly

may cause serious accident to the

operator.

Make sure that the blade is not bent,

warped, cracked, broken or damaged.

If you find any error to the blade, discard

it and change new one.

Cutting method

Fig. 19

1. Use the front left side cutting.

2. Guide the blade from your right to left with it

tilted slightly to your left.

3. When mowing a wide area, start working from

your left end to avoid interference of cut grass.

4. The blade may be seized by weeds if the engine

speed is too low, or the blade cuts too deep into

weeds. Adjust the engine speed and cutting

depth according to the condition of object.

If the grass or other object gets caught in

the blade, or if the unit starts to shake or

vibrate, turn off the engine and check the

whole unit. Change the blade if it has

been damaged.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm BCM1022 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info