Ferm
95
Periodisk vedligholdelse på båndpudseren / slibemaskinen kan forhindre
unnødige problemer
• Hold ydersiden af båndpudseren/slibemaskinen ren, så alle bevægelige dele kan køre
uhindret og fri for slitage.
• Udskift slibeskiven og slibebåndet, når disse er slidte.
• Båndpudserens styrevalser kræver ikke smøring.
Fejl
For det tilfælde, at maskinen ikke fungerer korrekt, er herunder angivet en række mulige
årsager med tilhørende løsningsforslag:
Reparationer må udelukkende udføres af en autoriseret installatør eller et
autoriseret serviceværksted.
Rengøring
Rengør regelmæssigt maskinkappen med en blød klud, helst efter hvert brug. Sørg for at
ventilationshullerne er fri for støv og snavs.
Brug en blød klud, der er vædet i sæbevand til at fjerne hårdnakket snavs. Brug ingen
opløsningsmidler, så som benzin, alkohol, ammoniak, osv. Den slags stoffer beskadiger
kunststofdelene.
Smøring
Maskinen behøver ingen ekstra smøring.
Fejl
Skulle en fejl opstå, f.eks. pga. slidtage af en enhed, kontakt venligst serviceadressen på
garantibeviset. På bagsiden af denne manual finder du en tegning med alle dele, der kan
bestilles.
• Der er tændt for
maskinen, men den kører
ikke
• Den elektriske motor
bliver varm
• Der er en afbrydelse i
strømforsyningen til
maskinen
• Tænd/sluk-knappen er
beskadiget
• Motoren er defekt
• Kontrollér, om der er et
brud på netledningen
• Kontrollér afbryderne
eller sikringerne i
strømforsyningen
• Kontakt venligst
serviceadressen på
garantibeviset
• Kontakt venligst
serviceadressen på
garantibeviset
GB
D
NL
F
E
P
I
S
FIN
N
DK
Ferm
• Is the belt grinder/linisher firmly mounted on a workbench?
• Because of the way it is used, the rotating parts of this belt grinder/linisher are not fully
covered. Therefore, take extreme care. Hold the workpiece firmly, so that it cannot fly out of
your hands and cause them to come into contact with the sanding belt or grinding wheel.
• The grinding wheel is a brittle part of this tool. The stone is not resistant to knocks.
Always grind on the front edge of the grinding wheel, and never on the side of the
grinding wheel. Never fit a cracked grinding wheel, as the high rotational speed could
cause the stone to fly apart, causing a serious accident.
• Always wear safety glasses when grinding or sanding.
• Never grind without using the eye shield.
• Avoid too much play between the tool rest and the grinding wheel or belt. With the
grinder, the play should be between 1 – 1.5 mm. The tool rest for the sanding belt
should be fixed such that the sanding belt can run freely.
• Only use the grinding wheel for the work it was designed for, for example, sharpening
tools. Do not use the grinding wheel for heavy construction work.
• Never ream out the hole in a grinding wheel to a larger diameter.
Whenever using the machine
In the interest of personal safety, only use accessories and auxiliary tools that
are recommended in the operator’s guide or in the catalogue. The use of other
than the mentioned accessories or auxiliary tools can lead to personal injury.
To avoid overheating, regularly allow the grinding machine to cool down. Use
the grinding machine for periods of no longer than 30 minutes.
• Check that the switch is NOT in the ON/’1’ position before connecting the machine to
the power supply.
• Always keep the power cord out of the way of the tool’s moving parts.
• Wear safety glasses.
• Wear a dust mask.
Immediately switch off the machine when:
• The machine overheats.
• The plug or power cord is defective or damaged.
• The switch is defective.
• You smell smoke or burning insulation.
Electrical safety
When using electric machines always observe the safety regulations applicable in your
country to reduce the risk of fire, electric shock and personal injury. Read the following
safety instructions and also the enclosed safety instructions.
Always check that the power supply corresponds to the voltage on the rating
plate.
6
GB
D
NL
F
E
P
I
S
FIN
N
DK
