Bedienungsanleitung Ferm BSM 1021 (Seite 5 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Norwegisch)

510079

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

2. SAFETY INSTRUCTIONS

Explanation of symbols

Denotes risk of personal injury, loss of

life or damage to the tool in case of

non-observance of the instructions in

this manual.

Indicates the presence of an electrical

voltage.

Wear eye protection.

Specic safety instructions

Hold the machine by the insulated gripping

surfaces where the accessory may contact hidden

wiring or the mains cable. If the accessory

contacts a ‘live’ wire, the exposed metal parts of

the machine can also become ‘live’. Risk of

electric shock.

• If you are working with the sanding machine,

wear always ear protectors and dust mask.

• The sanding machine is not suitable for wet

sanding.

• Check if the switch is not in position “ON”,

before you connect the mains plug to the

mains voltage.

• Keep the mains lead always away from

moving parts of the tools.

• Use safety glasses, especially when you sand

above your head.

• Do not bring pressure to your machine, this

will only delay the sanding.

Contact or inhalation of dust coming free

during sanding (e.g. lead painted

surfaces, woods and metals), can

endanger the health of operator and

bystanders. Always wear appropriate

personal equipment as a dust mask and

use the dust bag during sanding.

Immediately switch off the machine when:

• Excessive sparking of the carbon brushes and

verticiliosis in the collector.

• Interruption of the mains plug, mains lead or

mains lead damage.

• Defect switch

• Smoke or stench of scorched isolation

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of re, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Always check that the power supply

corresponds to the voltage on the rating

plate.

Class ll machine. Your machine is double

insulated; therefore no earthwire is

required.

Replacing cables or plugs

Immediately throw away old cables or plugs when

they have been replaced by new ones. It is

dangerous to insert the plug of a loose cable in

the wall outlet.

Using extension cables

Only use an approved extension cable suitable

for the power input of the machine. The minimum

conductor size is 1.5 mm

. When using a cable

reel always unwind the reel completely.

3. OPERATION

Always observe the safety instructions

and applicable regulations.

Choice of the sand-paper

Coarse sand-paper (grain 50) removes in general

the bigger part of the material and ne sand-

paper is used for the nishing. If the surface is not

even, then start with rough sand-paper. Further

you use middle coarse sand-paper(grain 80) to

remove the scratches left behind by the coarse

sand-paper and nally you take ne sand-paper

(grain 120) for the nishing.

Removing and Installing the sanding belt

Fig. C

Before assembly the sanding belt always

remove the plug from the mains.

• Put the machine on its side, with the drive belt

cover down wards.

• Loosen the sanding belt fastener (4).

• Remove the sanding belt from the machine

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm BSM 1021 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info