Bedienungsanleitung Ferm cdm 1076 (Seite 8 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

388434

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

8 Ferm

11-15: For driving screws into soft and medium-

density materials

16-20: For driving screws into hardwood

21-25: For driving large screws

Drill icon: For drilling

Hammer icon: For impact drilling

If material is particularly soft or porous,

set the torque clutch at a lower setting to

avoid overdriving the screw.

Adjusting the speed

Fig. 1

The appliance has two drill speeds.

For slow drilling or for driving or removing •

screws, set the speed selection switch (3) to

‘1’.

For fast drilling set the speed selection switch •

to ‘2’.

Never switch over when the motor is

running!

Driving and removing screws

Fig. 1

Set the direction reversing switch (8) to •

position ‘’ in order to drive screws.

Set the direction reversing switch (8) to •

position ‘’ in order to remove screws.

Ensure that the direction reversing

switch (8) is always set to ‘’ during

drilling.

Switching the device on and off

Fig. 1

Depress the on/off switch (9). It regulates the •

speed of the appliance by transmitting power

to the switch.

Release the on/off switch (9) to halt the drill •

chuck immediately, it will no longer run on.

Move the direction reversing switch (8) to the •

centre in order to lock the appliance in its

disabled state.

The drill will turn at its slowest speed when the

switch is depressed lightly. The drill will turn at its

fastest speed when the trigger is fully depressed.

Only lay down the appliance when it has stopped

running completely. Do not place it on a dusty

surface as particles of dust could get into the

mechanism.

Spirit level

Fig. 8

The drill is equipped with a dual reading horizontal/

vertical level to assist in keeping the drill “level”

while drilling horizontal and vertical holes. The

horizontal level (21) is located in the top of the drill

housing. The vertical level (22) is located on the

rear of the drill housing.

To maintain a level drilling position, hold the drill

where the level bubble is centred in the level

indicator circle.

LCD display

Fig. 9

This combi drill is equipped with an LCD display

(4) on top of the drill housing

To turn the display on, press the display button •

(27) once. To turn the display off, press the

display button again.

The light icon (25) will become visible when •

the LED work lights are turned on.

The clock (28) and minutes (24) remaining •

icons indicate the number of minutes of

running time that are available before the

battery requires recharging (Lithium Ion

battery only)

The battery icon (23) indicates the amount of •

charge remaining in the battery. Each charge

bar displayed indicates approximately 10%

charge remaining in the battery. A total of 10

charge bars indicates a fully charged battery.

Dual LED work lights

Fig. 1 + 9

Dual LED lights (12) are located behind the torque

ring. The LED light switch button (26) is located

below the LCD display on top of the drill.

To turn the LED lights on, press the LED light •

switch once.

To turn the LED lights off, press the LED light •

switch again.

The display must be turned on first, in order for the

LED lights to work.

5. SERVICE & MAINTENANCE

Make sure that the machine is not live

when carrying out maintenance work on

the motor.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm cdm 1076 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info