Ferm 13
16. Remove adjusting keys and wrenches.
Form the habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it on.
17. Avoid unintentional starting.
Do not carry plugged-in tools with finger on switch. Be
sure switch is off when plugging in.
18. Outdoor use extension cords.
When tool is used outdoors, use only extension cords
intended for use outdoors and so marked. Always use tool
in conjunction with a residual circuit breaker device.
19. Stay alert.
Watch what you are doing. Use common sense. Do not
operate tool when you are tired.
20. Check damaged parts.
Before further use of the tool, a guard or other part that is
damaged should be carefully checked to determine that it
will operate properly and perform its intended function.
Check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other
conditions that may affect its operation. A guard or other
part that is damaged should be properly repaired or
replaced by an authorized service centre unless otherwise
indicated elsewhere in this instructions manual. Have
defective switches replaced by an authorized centre. Do
not use tool if switch does not turn on and off.
21. Warning.
The use of any other accessory or attachment other than
recommended in this operation instructions or the
catalogue may present a risk of personal injury.
22. Have your tool repaired by an expert.
This appliance is manufactured to very high standards and
meets relevant safety regulations. Repairs should only be
done by a suitable qualified electrical engineer or
otherwise.
23. Hearing protection should be worn.
The following pictograms appear throughout these
operating instructions:
Indicates danger of injury, risk to life and possible
damage to the appliance if these instructions are
not followed.
Indicates the presence of electrical current.
Read through these operating instructions carefully
before using the appliance. Become familiar with the
functions and method of operation. To ensure proper
operation, always maintain the appliance according to
the instructions. The operating instructions and
associated documents should always be kept close to the
appliance.
When using power tools, you must observe the
follwing basic safety precautions in order to ensure
protection from electric shocks, injury and fire.
Read and follow all the instructions before using this
power tool. Look after the notes on safety.
• Remove the battery block. When the power tool is
not being used, prior to maintenance and when
changing tools such as the clamping chuck, and drill.
• The tool is suitable for use as a screwdriver and drill.
Any other application is specifically excluded.
IMPORTANT SAFETY NOTES ON CHARGER
AND BATTERY BLOCK
If you come into contact with acid from the battery
block, rinse it off with water immediately. If acid gets
into your eyes, rinse out your eyes at
once with water and contact a doctor immediately!
1. Read and note the operating instructions and safety
notes for the charger and battery block before use!
2. NB! Only use the charger and battery block that
were supplied by the manufacturer - otherwise you
will risk an accident.
3. Protect the charger, battery block and power tool
from moisture, e.g. rain or snow.
4. Always check that all cables are connected correctly
before using the charger.
5. If you discover that a cable is damaged, you should
not use the charger again. Have the damaged cable
replaced immediately.
6. When the charger is not in use, the mains plug should
be removed from the power socket. Do not pull out
the plug by grasping the cable.
7. If the charger has been dropped or has otherwise
been exposed to high mechanical stresses, you
should have it checked for damage by an authorised
dealer before using it again. Damaged parts should be
repaired.
8. Exercise caution when handling the battery block
and do not drop it or expose it to impacts.
9. Never attempt to repair the charger or battery block
yourself. Repairs must always be carried out by an
authorised dealer - otherwise you risk an accident.
10. Before cleaning or servicing the charger or battery
block, always pull the plug from the charger socket.
11. Never charge the battery block when the ambient
temperature is below 10°C or above 40°C.
12. The air vents in the charger must never be blocked.
13. The battery block must not be short-circuited.
A short-circuit will cause a high current to flow. This
may result in overheating, the danger of fire or
explosion of the battery block. This may damage the battery
block or the user may risk an accident.
Therefore:
1. Do not connect any cables to the poles of the battery
block.
2. Take care that there are no metal objects (nails, paper
clips, coins, etc.) on the contact surface of the battery
block.
3. Do not expose the battery block to water or rain.
4, Only use the battery block supplied in combination
with this cordless drill/screwdriver so as to avoid faults
and/or risks to persons.
14. A damaged battery block or one that can no longer
be charged must be disposed of as special waste. Do
not discard it with household waste.
15. Never throw the battery block onto a fire or into
water. This will risk explosion!
4 Ferm
