Bedienungsanleitung Ferm CDM1072 EBF-18K (Seite 6 von 28) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

538819

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Ferm 51

Hvis akku-boremaskinen ikke skal

bruges i en længere periode, skal

batteriet lades helt op forinden.

Batteriet skal være opladet under

opbevaringen.

5. SERVICE &

VEDLIGEHOLDELSE

Sørg for at maskinen ikke står under

strøm, når der udføres

vedligeholdelsesarbejder på

mekanikken.

Maskinerne er udviklet til at fungere længe uden

problemer med et minimum af vedligeholdelse.

Ved at rengøre maskinen regelmæssigt og

behandle den korrekt, bidrager De til en længere

levetid for maskinen.

Rengøring

Rengør regelmæssigt maskinkappen med en

blød klud, helst efter hvert brug. Sørg for at

ventilationshullerne er fri for støv og snavs. Brug

en blød klud, der er vædet i sæbevand til at

fjerne hårdnakket snavs. Brug ingen

opløsningsmidler, så som benzin, alkohol,

ammoniak, osv. Den slags stoffer beskadiger

kunststofdelene.

Smøring

Maskinen behøver ingen ekstra smøring.

Fejl

Skulle en fejl opstå, f.eks. pga. slidtage af en

enhed, kontakt venligst serviceadressen på

garantibeviset. På bagsiden af denne manual

finder du en tegning med alle dele, der kan

bestilles.

Miljø

For at undgå transportbeskadigelse leveres

maskinen i en solid emballage. Emballagen er så

vidt muligt lavet af genbrugsmateriale. Genbrug

derfor emballagen. NiCd celler kan genvindes.

Defekte og/eller kasserede elektriske

eller elektroniske maskiner skal

afleveres på en genbrugsplads.

Garanti

Læs det separat vedlagte garantikort for

garantibetingelserne.

06 Ferm

• The tool is suitable for use as a screwdriver

and drill. Any other application is specifically

excluded.

3. MOUNTING ACCESSORIES

Prior to mounting an accessory always

remove the battery.

Fitting and removing drill cutters

Fig. B

In addition to drill cutters, the tool can also

accommodate screwdriver bits with a hexagonal

shaft.

• Loosen the drill chuck (3) by rotating the

hand-grip (9).

• Insert the shaft of the drill cutter into the chuck.

• Tighten the drill chuck so that the drill cutter is

firmly clamped.

• Rotate the drill chuck in the opposite direction

when you wish to change the cutter.

Connecting and removing the battery

Fig. C

Ensure that the exterior of the battery

block or tool is clean and dry before

connecting the charger.

• Ensure that the direction reversing switch (5

Fig. A) is in the central position in order to

prevent the appliance from being switched on

unexpectedly.

• Insert the battery (4) into the base of the

appliance, as shown on the illustration. Push

the battery until it latches in.

• Press the locking buttons (10) on both sides

before removing the battery, and disengage

the battery from the base of the appliance.

4. OPERATION

Always follow the safety notes and the

relevant safety code.

Hold the appliance firmly and press the drills

steadily onto the workpiece. Do not overload the

appliance. Only use drills with no visible wear.

Worn drills will have a bad effect on the

functioning of the appliance.

Adjusting the torque

Fig. D

The appliance has 16 different torque settings

with which to set the power for driving and

removing screws.

• Set the torque adjustment ring (2) to the

desired position. The available torque settings

are indicated on the adjustment ring by the

numbers 1 to 8 and by dots between the

figures to define intermediate settings (16 in

total).

• You should preferably choose as low a setting

as possible when using the screwdriver.

Select a higher setting if the motor slips.

Driving and removing screws

• Set the direction reversing switch (5) to

position 'R' in order to drive screws.

• Set the direction reversing switch to position

'L' in order to remove screws.

Drilling

• Rotate the torque adjustment ring (2) to the

drilling position.

Ensure that the direction reversing

switch (5) is always set to 'R' during

drilling.

Switching the device on and off

Fig. A

• Depress the on/off switch (1). It regulates the

speed of the appliance by transmitting power

to the switch.

• Release the on/off switch (1) to halt the drill

chuck immediately which will no longer run on.

• Move the direction reversing switch (5) to the

centre in order to lock the appliance in its

disabled state.

Only lay down the appliance when it has stopped

running completely. Do not place it on a dusty

surface as particles of dust could get into the

mechanism.

Charging the battery

Fig. E

• Place the battery (5) inside the charger (11),

as shown on the illustration. Pay attention to

+ and - pole markings.

• Insert the charger plug into a power socket.

The red rapid charging lamp (12) should

now be illuminated.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CDM1072 EBF-18K Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info