Bedienungsanleitung Ferm CDM1075 FDCD-1440LK (Seite 7 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

538821

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Ferm

Loosen the drill chuck (6) by rotating the hand-•

grip (8).

Insert the shaft of the drill cutter into the chuck.•

Tighten the drill chuck so that the drill cutter is •

firmly clamped.

Rotate the drill chuck in the opposite direction •

when you wish to change the cutter.

Connecting and removing the battery

Fig.C

Ensurethattheexteriorofthebattery

blockortooliscleananddrybefore

connectingthecharger.

Ensure that the direction reversing switch •

(1, Fig. A) is in the central position in order to

prevent the appliance from being switched on

unexpectedly.

Insert the battery (3) into the base of the •

appliance, as shown on the illustration. Push

the battery until it latches in.

Press the locking buttons (2) on both sides •

before removing the battery, and disengage

the battery from the base of the appliance.

OPERATION

4. OPERATION

Alwaysfollowthesafetynotesandthe

relevantsafetycode.

Hold the appliance firmly and press the drill

steadily onto the workpiece. Do not overload

the appliance. Only use drills with no visible

wear. Worn drills will have a bad effect on the

functioning of the appliance.

Adjusting the speed

Fig.D

The appliance has two drill speeds.

For slow drilling or for driving or removing •

screws, set the speed selection switch (7) to ‘1’.

For fast drilling set the speed selection switch •

(7) to ‘2’.

Neverswitchoverwhenthemotoris

running!

Adjusting the torque

Fig.E

The appliance has 16 different torque settings

with which to set the power for driving and

removing screws.

Set the torque adjustment ring (5) to the •

desired position. The available torque settings

are indicated on the adjustment ring by the

numbers 1 to 8 and by dots between the

figures to define intermediate settings (16 in

total).

You should preferably choose a setting as •

low as possible when using the screwdriver.

Select a higher setting if the motor slips.

Driving and removing screws

Fig.A

Set the direction reversing switch (1) to •

position ‘’ in order to drive screws.

Set the direction reversing switch (1) to •

position ‘±’ in order to remove screws.

Drilling

Rotate the torque adjustment ring (5) to the •

drilling position.

Ensurethatthedirectionreversing

switch(1)isalwayssetto‘’during

drilling.

Switching the device on and off

Fig.A

Depress the on/off switch (4). It regulates the •

speed of the appliance by transmitting power

to the switch.

Release the on/off switch (4) to halt the drill •

chuck immediately, it will no longer run on.

Move the direction reversing switch (1) to the •

centre in order to lock the appliance in its

disabled state.

Only lay down the appliance when it has stopped

running completely. Do not place it on a dusty

surface as particles of dust could get into the

mechanism.

Charging the battery

The included battery is delivered in partly •

charged condition.

Only use the battery charger in a temperature •

range between + 5 °C to + 40 ºC.

Only use the battery charger in dry, ventilated •

rooms.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CDM1075 FDCD-1440LK Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info