Bedienungsanleitung Ferm CDM1076 FPCD-1800 (Seite 7 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

538822

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Ferm

Installing the depth stop rod

Fig. 1 + 2

The depth stop rod (13) is used as a gauge to

control the depth of the drilled hole. It can be used

with the combi drill in either the normal drilling

mode or the impact drill mode.

Turn the auxiliary handle (11) counter •

clockwise about three turns to open the depth

stop rod mounting clamp (14).

Insert the depth rod into the matching hole in •

the depth stop rod mounting clamp.

Position the depth stop rod so it will contact •

the work piece when the drill reaches the

appropriate depth.

When the depth stop rod is properly •

positioned, tighten the depth stop rod

mounting clamp by turning the auxiliary handle

clockwise.

Tighten the handle by hand only. Do not

over tighten the handle or you will

damage the handle or the housing.

Installing drill bits

Fig. 4

Never hold the chuck and use the drill

power to loosen or tighten bits. This can

result in serious injury.

To open the keyless drill chuck, rotate the •

chuck body (1) in a clockwise direction until

the jaws (16) open wide enough to accept the

bit. (17)

Insert the bit, over the full length of the jaws, •

into the chuck.

Tighten the chuck jaws onto the bit by turning •

the chuck body in a counter clockwise

direction.

As the chuck jaws begin to tighten on the bit, •

you will hear a clicking sound. Continue to

rotate the chuck body until the clicking stops

and you can no longer turn it any further by

hand. The chuck is now locked.

The bit must be properly inserted with all

three of the chuck jaws holding the bit

centred in the chuck. Make sure the

chuck jaws grasp the flat sides of a

screwdriver bit. Failure to do so could

cause the bit to be thrown from the

chuck, resulting in possible serious

injury or damage to the chuck.

To remove a bit, open the keyless drill chuck by •

rotating the chuck body in a clockwise direc tion

until the chuck jaws open and remove the bit.

Connecting and removing the battery

Fig. 1 + 5

Ensure that the direction reversing switch (8) •

is in the central position in order to prevent the

appliance from being switched on

unexpectedly.

Insert the battery into the base of the •

appliance, as shown on the illustration. Push

the battery until it latches in.

Press the locking button (10) on either side •

before removing the battery, and disengage

the battery from the base of the appliance.

Only use batteries of the following type. Using any

other batteries could cause serious injury or

damage the tool.

CDA1051: FPB-1800L, 18V Lithium-Ion

CDA1053: FPB-1800N, 18V NiMH

The following charger can be used to charge these

batteries.

CDA1052: FPL-1800 (Lithium-Ion and NiMH)

CDA1054: FPL-1800N (NiMH only)

4. OPERATION

Always follow the safety notes and the

relevant safety code.

Hold the appliance firmly and press the drill

steadily onto the workpiece. Do not overload the

appliance. Only use drills with no visible wear.

Worn drills will have a bad effect on the functio-

ning of the appliance. Do not cover the air vents.

This will reduce the motor cooling, and possibly

lead to overheating the motor.

Adjusting the torque

Fig. 6 + 7

Rotate the adjustment ring (2) to align the correct

torque setting number with the torque indicator

arrow (18). Use the chart below for the correct

torque setting:

1-5: For driving small screws

6-10: For driving medium sized screws into soft

materials

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CDM1076 FPCD-1800 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info