Bedienungsanleitung Ferm CDM1079 FPCD-1800I (Seite 5 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

539081

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Ferm

Loss of control can cause personal injury.

Use only impact drill bits and accessories that •

are designed for use with an impact drill when

using this machine in the impact drill mode.

Standard drill bits are NOT designed for use in

an impact drill and must NOT be used with an

impact drill. They may shatter and possibly

cause serious injury.

Do not drill material too small to be securely •

held.

Always keep hands out of the path of the drill •

bit. Avoid awkward hand positions where a

sudden slip could cause your hand to move

into the path of the drill bit.

Secure work piece. Use clamps or a vice to •

hold the work piece. It is safer than using your

hand and it frees both hands to operate the

tool.

Make sure there are no nails or foreign objects •

in the part of the work piece to be drilled.

To avoid injury from accidental starting, always •

remove the battery from the tool before

installing or removing a drill bit.

Do not install or use any drill bit that exceeds •

175 mm (7”) in lengths or extends more than

150 mm (6”) beyond the chuck jaws. They can

bend or break suddenly.

Before starting the operation, jog the switch •

shortly to make sure the drill bit does not

wobble or vibrate.

Do not use fly cutters or multiple-part hole •

cutters, as they can come apart or become

unbalanced during use.

Make sure the spindle has come to a complete •

stop before touching the chuck or attempting

to change the drill bit.

Always make sure the chuck is tight and the •

drill bit firmly tightened in the chuck before

starting the drill.

When drilling into smooth, hard surfaces such •

as metal, use a centre punch to mark the desi-

red hole location. This will prevent the drill bit

from slipping off centre as the hole is started.

Use a masonry bit with the drill in impact mode •

ONLY when drilling in concrete or masonry.

Always use carbide tipped masonry bits when •

drilling in concrete or masonry

This appliance is not intended for use by •

persons (including children) with reduced

sensory or mental capabilities, or lack of

experience and knowledge, unless they have

been given supervision or instructions

concerning use of the appliance by a person

responsible for their safety.

Children should be supervised to ensure that •

they do not play with the appliance.

Follow all safety rules and warnings,

also those which are included with the

battery pack and charger used with this

tool. Failure to do so may result in

serious injury or damage to the charger

and the battery pack

3. MOUNTING ACCESSORIES

Prior to mounting an accessory always

remove the battery.

Installing the auxiliary handle

Fig. 1+2+3

Install the auxiliary handle for two handed

operation of the drill. This is particularly important

for impact drilling in concrete. The auxiliary handle

can be installed on either the left or right side of

the Impact drill.

Insert the threaded mounting screw through •

the depth stop rod clamp (14) and into the

threaded hole in the housing.

Turn the auxiliary handle (11) clockwise to •

tighten it into the housing.

Make sure the key on the depth stop

clamp is aligned with the notch in the

drill housing. This will prevent it from

unexpected turning and the auxiliary

handle from coming loose.

Screwdriver bits and drill bits can be stored in the

auxiliary handle.

To remove the end cap (15), pull it of the auxiliary

handle. To install, push it back on the auxiliary

handle.

Installing the depth stop rod

Fig. 1+2

The depth stop rod (7) is used as a gauge to

control the depth of the drilled hole. It can be used

with the Impact drill in either the normal drilling

mode or the impact drill mode.

Turn the auxiliary handle (11) counter •

clockwise about three turns to open the depth

stop rod mounting clamp (14).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CDM1079 FPCD-1800I Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info