Bedienungsanleitung Ferm CDM1084 FDSD-1800NK (Seite 8 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

538824

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Ferm

For fast drilling set the speed selection switch

•

to ‘2’.

Never switch over when the motor is

running!

The pivot lock knob (4)

Fig. D

Turn the knob (4) anti clockwise to unlock the

head’s swing movement. The pivoting angle of the

chuck can be adjusted in 5 different positions

(0/22,5/45/67,5/90 degrees).

To lock again, rotate the knob clockwise when the

head is in the correct position. This can be felt by a

click.

Make sure the head’s swing movement

is locked before use by turning the knob

clockwise until it is locked. If it is not

possible to rotate the pivot lock knob (4),

move the head until this knob can rotate.

Then rotate the knob into its lock

position.

The rotation lock ring (2)

Fig. E

With the use of this ring the chuck can be rotated

360 degrees in 24 steps. Pull the ring backwards

and rotate the chuck into the required position.

Release the ring to lock the chuck into position.

Driving and removing screws

Fig. A

Set the direction reversing switch (5) to position

‘



’ in order to drive screws.

Set the direction reversing switch (5) to position

‘



’ in order to remove screws.

Ensure that the direction reversing

switch (5) is always set to ‘



’ during

drilling.

Switching the device on and off

Fig. A

Depress the on/off switch (8). It regulates the

•

speed of the appliance by transmitting power to

the switch.

Release the on/off switch (8) to halt the drill

•

chuck immediately, it will no longer run on.

Move the direction reversing switch (5) to the

•

centre in order to lock the appliance in its

disabled state.

Only lay down the appliance when it has stopped

running completely. Do not place it on a dusty

surface as particles of dust could get into the

mechanism.

Charging the battery

Fig. F

The FDCDL-1800 battery charger is only suitable

for charging batteries of type FDCDB-1800.

Place the battery inside the charger, as shown

•

on the illustration. Pay attention to + and - pole

markings.

Insert the charger plug into a power socket.

•

The red rapid charging lamp should now be

illuminated.

As soon as the green trickle charging lamp

•

lights up, charging has been completed and the

device is ready for operation.

Only use the charger in a dry

environment at temperatures between

5˚ C and 40˚ C.

The battery in your drill was not charged up at the

factory. Before using it for the first time, you should

charge it for approx. 1 - 2 hours so that it reaches

full capacity. The final capacity of the battery is

reached after 4 - 5 battery cycles.

Discharging the battery

Not only charging batteries is important,

discharging is of equal importance or

even greater importance.

When the battery is charged the cordless drill

•

has to be used until you start noticing that the

power of the drill is diminishing and that the

maximum rotational speed is not reached.

The battery is almost discharged now. Only

•

now you can start charging the battery.

Charging the battery while it is still charged for

•

say one-third of capacity, the so-called

‘memory effect’ can occur. Since during

charging only the discharged part of the battery

capacity of the battery is being charged now,

the battery can start crystallizing in the one-

third that is still charged. This part of the battery

capacity can never be used afterwards.

Do not discharge the battery to the minimum.

•

As soon as you notice that the power or the

maximum rotational speed is diminishing, you

have to charge the battery.

CDM1084 # Ma 0807-16.1.indd 8 16-07-2008 11:43:59

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CDM1084 FDSD-1800NK Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info