Bedienungsanleitung Ferm CDM1087 - FPDW-1800 (Seite 4 von 36) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

632671

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

4 Ferm

3. MOUNTING ACCESSORIES

Prior to mounting an accessory always

remove the battery.

Connecting and removing the battery

Fig. 1 + 2

Ensure that the direction reversing switch (6) •

is in the central position in order to prevent the

appliance from being switched on

unexpectedly.

Insert the battery into the base of the •

appliance, as shown on the illustration. Push

the battery until it latches in.

Press the locking button (4) on either side •

before removing the battery, and disengage

the battery from the base of the appliance.

Only use batteries of the following type. Using any

other batteries could cause serious injury or

damage the tool.

CDA1051: FPB-1800L, 18V Lithium-Ion

CDA1053: FPB-1800N, 18V NiMH

The following charger can be used to charge these

batteries.

CDA1052: FPL-1800 (Lithium-Ion and NiMH)

CDA1054: FPL-1800N (NiMH only)

4. OPERATION

Operation

The impact wrench is driven by an electric motor

via a gear and impact mechanism.

The impact mechanism starts when the screwed

connection runs tight and load is put on the motor.

The mechanism converts the power of the motor

to steady rotary impacts.

Always observe the safety instructions

and applicable regulations.

Fig. 1

Firmly hold the machine and push the bit with even

pressure into the workpiece. Do not force the

machine.

Use only bits that do not yet show any signs of

wear. Worn bits have a negative effect on the

efficiency of the machine.

Screwing screws in and out

• Setthedirectionswitch(6)onposition‘4’ for

putting in screws.

• Setthedirectionswitchonposition‘3’ for

removing screws.

Be sure that the direction switch (6)

always in position ‘4’ during drilling.

Regular check the chuck for possible

damage.

Possible use a coolant. In case of

drilling in walls, watch out for drilling in

electric wires of water pipes. Get advice

according to the use from your dealer.

Switching on and off

Fig. 1

• Presstheon/offswitch(7)in.Youregulatethe

speed of the machine by the degree to which

you keep the switch pressed in.

• Releasingtheon/offswitch(7)causesthedrill

to stop immediately

• Slidethedirectionswitch(6)tothemiddleto

lock the machine in switched off mode.

Do not put the machine away until the machine

has completely stopped running. Do not store the

machine on a dusty surface. Dust particles can get

into the mechanism.

Only operate the drill with the forward /

reverse switch (7) fully engaged. Never

attend to use the drill with this switch in

the neutral position.

5. SERVICE & MAINTENANCE

Make sure that the machine is not live

when carrying out maintenance work on

the motor.

The machines have been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CDM1087 - FPDW-1800 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info