Bedienungsanleitung Ferm CDM1094 (Seite 5 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

539082

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Ferm

Thermic protector

Do not dispose of in household waste.

Wear ear and eye protection

Wear a dust mask. Working with wood,

metals and other materials may produce

dust that is harmful to health. Do not

work with material containing asbestos

Indoor use only

In case of failure, the transformer is not

dangerous

Do not use in rain

Specific safety instructions

For use of this machine/tool:

• Inspect the surface to be drilled for hidden

electrical wiring, gas pipes or other obstacles

(for example, using a metal detector).

• Check the following points:

• Does the appliance’s voltage correspond

with the mains power supply voltage?

• Are power cords, insulation and plug in

good order: sound, not loose or damaged?

• Is there a good, firm connection at the

mains socket?

• Does the drill show any sign of abnormal

running, overheating or excessive

sparking?

• Whenever any of the problems mentioned

above appear, immediately cease using

the machine and have it repaired by an

expert.

• Wear ear protectors. Exposure to noise can

cause hearing loss.

Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring or its own

cord. Cutting accessory contacting a “live” wire

may make exposed metal parts of the power tool

“live” and give the operator an electric shock.

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Always check that the mains voltage is

the same as on the type plate of the

machine

Class II machine – Double insulation –

You don’t need any earthed plug

Replacement of power cords or plugs

Immediately dispose of old cords and plugs once

they have been replaced.

It is dangerous to plug a loose power cord into a

mains power socket.

Use of extension leads

Only ever use approved extension leads that are

suitable for the power rating of the machine. The

mini mum core thickness is 1.5 mm

. Whenever

using a reel extension lead, always fully unroll the

lead.

3. OPERATING

Hammer drills require very little operator

pressure. Excessive pressure on the

tool can lead to unnecessary

overheating of the motor, and burning of

the driven tool

Exchanging and removing drill bits

Fig. A

Inspect bits regularly during use. Blunt

bits should be re-sharpened or replaced

• Lightly oil the bit shaft before inserting it into

the chuck.

• Slide the locking sleeve (2) to the rear, and

insert the bit into the chuck opening. Ensure

that the keyway in the bit is seated properly in

the chuck, by carefully turning the bit until it

clicks into place. Release the locking sleeve.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CDM1094 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info