Bedienungsanleitung Ferm CDM1104 (Seite 6 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

510082

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

Replacing cables or plugs

Immediately throw away old cables or plugs when

they have been replaced by new ones. It is

dangerous to insert the plug of a loose cable in

the wall outlet.

• Remove the battery block when the power tool

is not being used and prior to maintenance.

• The tool is suitable for use as a screwdriver

and drill. Any other application is specically

excluded.

3. MOUNTING ACCESSORIES

Prior to mounting an accessory always

remove the battery.

Fitting and removing drill cutters

Fig. B

In addition to screwdriver bits with a hexagonal

shaft, this tool can also accommodate drill bits

with a hexagonal shaft.

• Loosen the drill chuck (4) by rotating the hand-

grip (9).

• Insert the shaft of the drill cutter into the chuck.

• Tighten the drill chuck so that the drill cutter is

rmly clamped.

• Rotate the drill chuck in the opposite direction

when you wish to change the cutter.



Fig. C

Ensure that the exterior of the battery

block or tool is clean and dry before

connecting the charger.

• Ensure that the direction reversing switch (1,

Fig. A) is in the central position in order to

prevent the appliance from being switched on

unexpectedly.

• Insert the battery (3) into the base of the

appliance, as shown on the illustration. Push

the battery until it latches in.

• Press the locking buttons (2) on both sides

before removing the battery, and disengage

the battery from the base of the appliance.

4. OPERATION

Always follow the safety notes and the

relevant safety code.

Hold the appliance rmly and press the drill

steadily onto the work piece. Do not overload the

appliance. Only use drill bits with no visible wear.

Worn bits will have a bad effect on the functioning

of the appliance.

Adjusting the torque

Fig. D

The appliance has 16 different torque settings

with which to set the power for driving and

removing screws.

• Set the torque adjustment ring (3) to the

desired position. The available torque settings

are indicated on the adjustment ring by the

numbers 1 to 8 and by dots between the

gures to dene intermediate settings (16 in

total).

• You should preferably choose a setting as low

as possible when using the screwdriver. Select

a higher setting if the motor slips.

Driving and removing screws

• Set the direction reversing switch (6) to

position ‘R’ in order to drive screws.

• Set the direction reversing switch to position ‘L’

in order to remove screws.

Drilling

• Rotate the torque adjustment ring (3) to the

drilling position.

Ensure that the direction reversing

switch (6) is always set to ‘R’ during

drilling.

Switching the device on and off

Fig. A

• Depress the on/off switch (1). It regulates the

speed of the appliance by transmitting power

to the switch.

• Release the on/off switch (1) to halt the drill

chuck immediately which will no longer run on.

• Move the direction reversing switch (6) to the

centre in order to lock the appliance in its

disabled state.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CDM1104 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info