Bedienungsanleitung Ferm CDM1132 (Seite 6 von 96) (Alle Sprachen)

762254

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work

patterns.

Description

The numbers in the text refer to the diagrams on

pages 2-3

Fig. A

1. Machine

2. Charging socket

3. Charging indication light

4. Bit holder

5. Direction switch

6. On / off switch

7. Work light

8. Charger adaptor

10. Screw driver bit

3. OPERATING

The machine must be charged before

first use.

Charging the machine

• Plug the small cable plug (8A) into the

machine’s charging socket (2).

• Plug the charger into an electrical outlet

and wait for a while. The LED indicator on

the machine (3) will lighten up and show the

charging status.

Charging indication light (3)

Fig.A

The machine has a charging indication light

(3) which indicates the status of the charging

process:

LED Status

Blinking Battery charging in progress

Continuous Battery charging finished, battery fully charged

• Fully charging the battery may take up to 3 - 5

hours.

Fitting and removing drills or screwdriver bits

Fig. B

The machine bit holder (4) is suitable for drills

and screwdriver bits with a standard ¼ inch.

hexagonal shaft. To fit a screwdriver bit:

• Insert the screw driver bit (10) into the

machine’s bit holder (4), it will be hold by a

magnet.

• The screw driver bit can be removed by pulling

it out of the bit holder again.

Adjusting the direction of rotation

Fig. A

• Set the direction switch (5) to position ‘’ in

order to drive screws or to use it for drilling.

• Set the direction switch (5) to position ‘’ in

order to remove screws.

Switching the machine on and off

Fig. A

• Pressing the on/off switch (6) will activate the

machine.

• Releasing the on/off switch (6) will stop the

machine.

• Move the direction switch (5) to the middle

position to lock the movement of the on/off

switch. It cannot be activated in this position.

The machine is equipped with electronic

overload protection function. When the

machine gets overloaded it will shut

down automatically. When this happens,

please wait for at least 5 seconds to let

the overload protection reset itself.

Spindle lock function

The machine is fitted with an automatic spindle

lock feature. When the on/off switch (6) is not

pressed, the bit holder (4) rotation is locked. Now

it is possible to use the screwdriver (even when

the battery is empty) as a manual tool.

4. MAINTENANCE

Before cleaning and maintenance, always

switch off the machine and remove the

battery pack from the machine.

Clean the machine casings regularly with a soft

cloth, preferably after each use. Make sure that

the ventilation openings are free of dust and

dirt. Remove very persistent dirt using a soft

cloth moistened with soapsuds. Do not use any

solvents such as gasoline, alcohol, ammonia,

etc. Chemicals such as these will damage the

synthetic components.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CDM1132 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info