Bedienungsanleitung Ferm CDM1134 (Seite 7 von 36) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

763642

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

• Position 1: For slow drilling, large drilling

diameter or screw driving. The machine has

high power at a low speed.

• Position 2: For fast drilling or small drilling

diameter

Adjusting the direction of rotation

Fig. E

• Set the direction switch (9) to position in

order to drive screws or to use it for drilling.

• Set the direction switch (9) to position in

order to remove screws.

Switching the machine on and off

Fig. E

The on/off switch (10) is used for activating the

machine and adjusting rotation speed.

• Pressing the on/off switch (10) will activate

the machine, the further the switch is being

pushed, the faster the drill will turn.

• Releasing the on/off switch (10) will stop the

machine.

• Move the direction reversing switch (9) to the

middle position to lock the movement of the

on/off switch.

Adjusting the torque

Fig. E

The machine has 17 different torque settings

and a special drill mode to set the power being

transmitted to the chuck.

By rotating the torque adjustment ring (11),

screws can be driven to a predetermined depth,

which is ideal for repetitive work. The higher the

number, the more torque will be transmitted.

• Select a low setting for small screws or soft

work material.

• Select a high setting for large screws, hard

work materials and when removing screws.

• You should preferably choose a setting as

low as possible when driving screws. Select

a higher setting if the motor slips before the

screw is fully tightened.

• For drilling, turn the torque adjustment ring (11)

to the setting for drilling ( ) by fully turning it

counterclockwise.

Ensure that the direction switch (9) is

always set to during drilling.

The machine is equipped with electronic

overload protection function. When the

machine gets overloaded it will shut

down automatically. When this happens,

please wait for a few seconds to let the

overload protection reset itself.

4. MAINTENANCE

Before cleaning and maintenance, always

switch off the machine and remove the

battery pack from the machine.

Clean the machine casings regularly with a soft

cloth, preferably after each use. Make sure that

the ventilation openings are free of dust and

dirt. Remove very persistent dirt using a soft

cloth moistened with soapsuds. Do not use any

solvents such as gasoline, alcohol, ammonia,

etc. Chemicals such as these will damage the

synthetic components.

ENVIRONMENT

Faulty and/or discarded electrical or

electronic apparatus have to be collected

at the appropriate recycling locations.

Only for EC countries

Do not dispose of power tools into domestic

waste. According to the European Guideline

2012/19/EC for Waste Electrical and Electronic

Equipment and its implementation into national

right, power tools that are no longer usable must

be collected separately and disposed of in an

environmentally friendly way.

WARRANTY

The warranty conditions can be found on the

separately enclosed warranty card.

The product and the user manual are subject

to change. Specifications can be changed

without further notice.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CDM1134 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info