Bedienungsanleitung Ferm CDM1136 (Seite 8 von 20) (Englisch, Holländisch)

763853

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

3. OPERATING

The machine must be charged before

first use.

Charging the machine

Fig. B

In order to charge the machine, insert the small

plug of the charger adapter (8) into the charging

socket (2) on the bottom of the machine.

Subsequently plug the mains plug connector of the

charger adapter (8) into a socket outlet. The battery

indication light (3) will show the charging progress.

Fully charging the battery may take up to 3-5 hours.

Checking the battery charge status

Fig. C

The battery indication light (3) shows the remaining

battery charge when the battery indication light

button (9) is pressed.

The battery indication light

(3) has three lights indicating the remaining charge

level. The more

lights that burn, the more charge

the battery has left.

When the RED light is burning,

it means the battery is almost empty and should

be charged.

Fitting and removing drills or screwdriver bits

Fig. D

The machine bit holder (4) is suitable for drills and

screwdriver bits with a standard ¼ inch hexagonal

shaft. To fit a screwdriver bit:

• Insert the screw driver bit (10) into the

machine’s bit holder (4), it will be hold by a

magnet.

• The screw driver bit can be removed by pulling

it out of the bit holder again.

Adjusting the direction of rotation

Fig. F

• Set the direction switch (5) to position ‘L’ in

order to drive screws or to use it for drilling.

• Set the direction switch (5) to position ‘R’ in

order to remove screws.

Switching the machine on and off

Fig. F

• Pressing the on/off switch (6) will activate the

machine.

• Releasing the on/off switch (6) will stop the

machine.

• Move the direction switch (5) to the middle

position to lock the movement of the on/off

switch. It cannot be activated in this position.

The machine is equipped with electronic

overload protection function. When the

machine gets overloaded it will shut

down automatically. When this happens,

please wait for at least 5 seconds to let

the overload protection reset itself.

Spindle lock function

The machine is fitted with an automatic spindle

lock feature. When the on/off switch (6) is not

pressed, the bit holder (4) rotation is locked. Now

it is possible to use the screwdriver (even when

the battery is empty) as a manual tool.

Adjustable handle

Fig. E

The machine features an adjustable handle that

can be adjusted in two positions, for hard to reach

places.

Press the lock button (11) and turn the handle of

the machine to the desired angle.

Adjusting the torque

Fig. F

The machine has 6 different torque settings

and a special drill mode to set the power being

transmitted to the chuck.

By rotating the torque adjustment ring (12),

screws can be driven to a predetermined depth,

which is ideal for repetitive work. The higher the

number, the more torque will be transmitted.

• Select a low setting for small screws or soft

work material.

• Select a high setting for large screws, hard

work materials and when removing screws.

• You should preferably choose a setting as

low as possible when driving screws. Select

a higher setting if the motor slips before the

screw is fully tightened.

• For drilling, turn the torque adjustment ring (12)

to the setting for drilling ( ) by fully turning it

counterclockwise.

Ensure that the direction switch (5) is

always set to "L" during drilling.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CDM1136 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info