Bedienungsanleitung Ferm CDM1142P (Seite 7 von 108) (Alle Sprachen)

762315

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

•

Plug the charger plug into an electrical outlet

and wait for a while. The LED indicators on

the charger (6) will lighten up and show the

charger status.

LED indicators (6)

Fig.C

The charger has 2 LED indicators (6) which

indicate the status of the charging process:

Red LED

status:

Green LED

status: Charger status

Off Off No power

On Off

Standby mode:

-No battery is inserted or,

-Battery inserted but charging has

finished more then 2 hours ago

Blinking Blinking Defective battery

On Blinking Battery charging in progress

On On Battery charging finished, battery

fully charged

Blinking Off

Battery is too hot, charging

progress is on hold. Charging will

start automatically after the battery

has cooled down.

• Fully charging the battery may take up to 60

minutes.

• After the battery is fully charged remove the

charger plug from the outlet and remove the

battery from the charger.

• The battery can be stored or directly installed

on the machine.

Lithium-Ion cells can be stored for a long

period without losing much of their

charge. When the machine is not being

used over a longer period of time it is best

to store the battery in charged condition.

Quick-Release Chuck

Use only 1/4” (6.35 mm) hex impact

accessories. Non-impact accessories

may break and cause a hazardous

condition. Inspect accessory prior to use

to ensure that it contains no cracks.

Place the direction switch (10) in the lock-off

(centre) position or remove battery pack before

changing accessories. To install an accessory,

fully insert the accessory. The accessory is locked

into place. To remove an accessory, pull the chuck

collar (8) away from the front of the tool. Remove

the accessory.

Adjusting the direction of rotation

Fig. A

• Set the direction switch (10) to position “” in

order to drive screws or to use it for drilling.

• Set the direction switch (10) to position “” in

order to remove screws

Switching the machine on and off

Fig. A

The on/off switch (11) is used for activating the

machine and adjusting rotation speed.

• Pressing the on/off switch (11) will activate

the machine, the further the switch is being

pushed, the faster the drill will turn.

• Releasing the on/off switch (11) will stop the

machine.

•

Move the direction reversing switch (10) to the

middle position to lock the movement of the on/

off switch. It cannot be activated in this position.

Only lay down the machine when it has

stopped running completely. Do not

place it on a dusty surface as particles of

dust could get into the mechanism.

Work light (9)

Fig. A

The machine is equipped with a work light to

illuminate the work location.

• It automatically switches on when the on/off

switch is being pressed.

• It automatically switches off when the on/off

switch is released again.

Belt hook (12)

Fig. A

The machine is equipped with a belt hook for

hanging the machine to your belt during use.

Always switch the direction switch (10) to

middle position to avoid accidental

startup of the machine.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CDM1142P Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info