Bedienungsanleitung Ferm CDM1146 (Seite 10 von 72) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch, Alle Sprachen)

762290

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

ensures that the tool spindle is locked and the

blade screw can be loosened.

• Set the direction switch (5) to the middle

position.

• Remove the blade guard (15) by loosing the

blade guard screw(18) (fig. E), lift up the left

side and slide to the right.

• Unscrew the blade screw (16) (fig. F).

• Remove the blade (17)

• Place the new blade, ensure that the sloping

edge of the blade faces you (fig. G)

• Retighten the blade screw (16)

• Place the blade guard (15) back and retighten

the blade guard screw (18).

Working Advice

Do not overload the machine, when

overloading the machine it may come to

a standstill.

• The cutting performance depends on the

materials to be cut. When machine is fully

charged the result will be better.

• Always make sure the blade is clean and free

form excess materials.

• Make sure nothing can get wedged during

cutting by holding the guide edge (14) parallel

to the cutting surface.

• Especially thin materials, such as fabrics, can

be pulled into the machine during cutting.

Always be careful and do not apply too much

pressure in order to achieve good cutting

results. Apply sufficient tension to the fabrics

and cut slowly.

• Improper use of the blade will cause it to

become blunt.

• Optimum cutting results are best determined

through testing on a small part of the material.

4. MAINTENANCE

Before cleaning and maintenance, always

switch off the machine and/or remove the

battery pack from the machine.

• Remove the cutting adapter from the

screwdriver to clean it. There is danger of

injury when unintentionally actuating the On/

Off switch.

• Be careful when cleaning the blade and

counterblade. The blades have sharp edges

which you can injure yourself on.

Clean the machine casings regularly with a soft

cloth, preferably after each use. Make sure that

the ventilation openings are free of dust and

dirt. Remove very persistent dirt using a soft

cloth moistened with soapsuds. Do not use any

solvents such as gasoline, alcohol, ammonia,

etc. Chemicals such as these will damage the

synthetic components.

ENVIRONMENT

Faulty and/or discarded electrical or

electronic apparatus have to be collected

at the appropriate recycling locations.

Only for EC countries

Do not dispose of power tools into domestic

waste. According to the European Guideline

2012/19/EC for Waste Electrical and Electronic

Equipment and its implementation into national

right, power tools that are no longer usable must

be collected separately and disposed of in an

environmentally friendly way.

WARRANTY

FERM products are developed to the highest

quality standards and are guaranteed free of

defects in both materials and workmanship for the

period lawfully stipulated starting from the date

of original purchase. Should the product develop

any failure during this period due to defective

material and/or workmanship then contact your

FERM dealer directly.

The following circumstances are excluded from

this guarantee:

• Repairs and or alterations have been made

or attempted to the machine by unauthorized

service centers.

• Normal wear and tear.

• The tool has been abused, misused or

improperly maintained.

• Non-original spare parts have been used

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CDM1146 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info