Bedienungsanleitung Ferm COM1007P (Seite 9 von 96) (Alle Sprachen)

697794

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

• Press the spindle lock button (9) in order to

block the movement of the machine spindle.

• Keep pressing the spindle lock button (9).

Place the wrench (16) on the disk bolt and turn

it slightly until the button (9) is pushed in to the

max and the spindle rotation is blocked.

• Remove the bolt (21), small washer (20), the

big outer washer(19)

• Then remove the cutting disk (3)

Mounting a cutting disk

• In case this has not been done yet, remove the

bolt (21) by turning it counterclockwise, then

remove small washer (20) and the big outer

washer(19).

• Place the cutting disk (3) on the machine

spindle.

• First add the big outer washer (19), then the

small washer (20) and then the fixing bolt (21)

according to fig C. and tighten it by hand until

the spindle starts rotating.

• Press the spindle lock button (9) in order to

block the movement of the machine spindle.

• Keep pressing the spindle lock button (9).

Place the wrench (16) on the disk bolt and turn

it slightly in clockwise direction.

• When the spindle lock blocks the rotation,

tighten the disk bolt by using the wrench (16).

• Loosen the spindle lock button and ensure the

spindle lock button is not blocking the spindle

anymore.

Then check if the wheel is assembled correctly:

• Turn the disk (3) by hand a few rounds to check

if it is turning freely and if it is aligned well.

• Turn the machine on and let the machine run

for at least 3 minutes.

The On/Off switch

Fig. B

The On/Off switch (7) is activated by manually

pulling the switch trigger. It is cut of by releasing

the trigger again.

The workpiece clamp (5)

Fig. A & B & D

• Place the workpiece material between front

clamp (13) and rear clamp (12).

• Raise the stopper(14) like shown in Fig. D. and

rotate the screw handle (15) forward until the

front clamp (13) touches the work piece.

• Then move the stopper (14) down (to lock the

spindle) and securely fix the workpiece by

turning the screw handle (15).

Cutting at angles

Fig. E

The machine permits cutting at angles from 0

by adjusting the rear clamp (12).

• Loosen the 2 M10 hexagon socket head bolts

(22 & 23) which hold the rear clamp (12) until

the vice can move.

• Then set the rear clamp (12). to the correct

angle and tighten both bolts (22 & 23) again.

Moving the rear vice (to cut bigger work

pieces)

Fig. F

The vice permits a maximum workpiece size of

160mm when shipped from the factory. The vice

can be adjusted in to the rear to permit workpiece

size of 195 mm like shown in the right picture (fig. F).

• Loosen the 2 M10 hexagon bolts (22 & 23) on

the rear clamp (12) completely.

• Move the clamp (12) backwards and fix the

bolts (22 & 23) to the rear connection holes

again.

Adjusting the depth stop:

Fig.B

The machine is equipped with a depth stop bolt,

with this bolt the maximum cutting depth can be

adjusted.

• If the depth cutting depth needs to be

adjusted, loosen the lower nut (10B), then

adjust the depth setting by turning the upper

bolt (10A) to the desired positions.

• Then fix the lower nut (10B) again.

Cutting procedure:

In order to cut material always follow following

procedure:

• Make sure the workpiece is clamped and

supported well before starting the machine.

• Start the machine in upper position let it run for

a while until it reaches max. speed.

• Ensure the blade is turning freely without

vibration.

• Gently move down the machine until it touches

the material.

• Keep pushing the handle with little force, make

sure the blade speed is not dropping.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm COM1007P Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info