Bedienungsanleitung Ferm CRM1041 (Seite 7 von 36) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

632694

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Ferm

sloping and smooth, make sure that the

compressor will not move when in operation. If the

surface area is a board or a shelf of a bookcase,

just make sure that they cannot fall down by

securing them properly. For proper ventilation and

effective cooling, it is important that the

compressor is positioned at least 100 cm from the

wall (fig. 4).

Make sure that the compressor is

transported in the right way, do not turn it

upside down and don’t lift it with hooks or

ropes (fig. 5-6).

Starting up

• Check whether the mains voltage corresponds

to that indicated on the electrical specification

plate (fig. 10), the permitted tolerance range

should be within 5%.

• Press the switch situated on the upper part

into the “0” position according to the pressure

regulator type fitted on the device (fig. 11). Put

the power plug in the plug socket (fig. 9) and

start the compressor by pulling the switch (3)

to the “I” position. The operation of the

compressor is fully automatic. The pressure

regulator will stop the compressor when the

maximum value has been reached and start it

up when the pressure drops below the

minimum value. Normally the difference in

pressure is approx. 2 Bar/29 psi between the

maximum and the minimum value. For

instance - The compressor will stop when it

reaches 8 Bar (116 psi) (this is the maximum

operating pressure) and will start up

automatically when the pressure within the

tank has dropped to 6 Bar (87 psi).

The head/cylinder/transmission pipe

assembly may reach high temperatures,

so take care when working close to these

parts and do not touch them to avoid

burns (fig. 12 - 13).

Adjusting the operating pressure

Fig. 14

It is not necessary continuously to use the

maximum operating pressure, the compressed-air

tools often require less pressure. With regard to

compressors supplied with a pressure reduction

valve it is necessary to set the operating pressure

properly.

It is possible to set the operating pressure by

(fig. 14) using the turning knob on the reduction

valve (5)

• By turning clockwise, the pressure will be

increased.

• By turning anti-clockwise, the pressure will be

reduced.

The set pressure can be locked by turning the ring

under the turning knob in the opposite direction

from the turning knob thereby fixing the turning

knob. The set pressure is visible on the

manometer of the reduction valve.

4. Maintenance

Make sure that the plug is removed from

the mains when carrying out maintenance

work on the motor.

The machines have been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning. Before interfering in any way whatsoever

with the compressor, please make sure that:

• The switch button is in the “0” position and the

power plug is removed from the power socket

• The pressure regulator and the switches on

the switch board are switched off in the “0”

position.

• The air tank is fully decompressed (both

pressure gauges must be pointed at 0 Bar)

Malfunction

Should the machine fail to function correctly, a

number of possible causes and the appropriate

solutions are given below:

Air loss

• Check all air connections by wetting them with

a soapy water solution ( Never use the

solution nearby electric connections )

• When the tank is empty and being filled. The

user might hear a sisseling sound by the

pressure switch. This is normal and will stop

before the compressor reach a pressure of 1.5

bar

• Check if the drain valve ( 10 ) is closed well

The compressor runs but does not compress

Fig. 19

• May be caused by the valves (C-C2) or a

gasket (B1-B2) being broken.

• Replace the damaged part.

CRM1041 Ma 1403-18.indd 7 4/24/14 10:16 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CRM1041 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info