Bedienungsanleitung Ferm CRM1045 (Seite 7 von 64) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

632691

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

to the instructions represented in fig. 2. Place the

compressor on a flat surface or at a maximum slope

of10°(fig.3),inawellventilatedarea,protected

against atmospheric factors and not in explosive

surroundings.Ifthesurfaceareaisslopingand

smooth,makesurethatthecompressorwillnot

movewheninoperation.Ifthesurfaceareaisa

boardorashelfofabookcase,justmakesurethat

they cannot fall down by securing them properly.

Forproperventilationandeffectivecooling,itis

important that the compressor is positioned at least

100 cm from the wall (fig. 4).

Make sure that the compressor is

transported in the right way, do not turn it

upside down and don’t lift it with hooks

or ropes (fig. 5-6).

Filling the compressor with oil.

Your compressor is supplied with oil which is

already included in the carter.

Beforeuse,removethetransportcaponthecarter

(12),andreplaceitbytheregularoilcap(fig7).

Beforeuse,ensurethatoillevelissufficient.

This can be checked by checking the oil

inspectionglass(13).Whencompressorisplaced

horizontally,theoillevelshallreachtheredmark.

Installing the air filters.

Remove the transport lids and replace them with

the supplied air filters before using the compressor.

Starting up

• Checkwhetherthemainsvoltagecorresponds

to that indicated on the electrical specification

plate(fig.10),thepermittedtolerancerange

should be within 5%.

• Presstheswitch(3)situatedontheupperpart

intothe“0”positionaccordingtothepressure

regulator type fitted on the device (fig. 11).

• Puttheplugintheplugsocket(fig.9)andstart

the compressor up by putting the switch(3)

ofthepressureregulatorinthe“I”position.

The operation of the compressor is fully

automatic. The pressure regulator will stop

the compressor when the maximum value has

been reached and start it up when the pressure

drops below the minimum value. Normally

the difference in pressure is approx. 2 Bar/29

psi between the maximum and the minimum

value.Forinstance-Thecompressorwillstop

when it reaches 8 Bar (116 psi) (this is the

maximum operating pressure) and will start

up automatically when the pressure within the

tank has dropped to 6 Bar (87 psi).

The head/cylinder/transmission pipe

assembly may reach high temperatures,

so take care when working close to these

parts and do not touch them to avoid

burns (fig. 12 - 13).

Adjusting the operating pressure

Fig. 14

Itisnotnecessarycontinuouslytousethe

maximumoperatingpressure,thecompressed-air

toolsoftenrequirelesspressure.Withregardto

compressors supplied with a pressure reduction

valve it is necessary to set the operating pressure

properly.

Itispossibletosettheoperatingpressureby

using the turning knob(5) on the reduction valve.

• Byturningclockwise,thepressurewillbe

increased.

• Byturninganti-clockwise,thepressurewillbe

reduced.

The compressor has two pressure gauges and

onepointtoconnectanairhose:

• Pressuregauge(7):Thepressureofthisoutlet

can be regulated with help of the reduction

valve (5).

• Pressuregauge(8):tankpressure

Hintsforaccurateadjustmentofthepressure

regulation:

• Turntheturningknob(5)anti-clockwisetill

pressure is fully released

• Connecttheairtoolyouwanttousetothe

quick coupler (6)

• Activatetheairtoolshortly,sothepressure

gauge (7) will show the right pressure level

• Turntheturningknob(5)clockwise,tillthe

pressure gauge (7) shows the pressure level

you need

• Yourairtoolisnowreadytouse.

Note:whennotconnectinganairtoolwhile

adjustingthepressure,itmightoccurthepressure

gauge (7) is not reacting accurately on the

pressure drop.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CRM1045 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info