Bedienungsanleitung Ferm CSM1030 - FKS-185 (Seite 5 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

763364

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Ferm

guard does not move freely and close

instantly. Never clamp or tie the lower guard

into the open position. If saw is accidentally

dropped, lower guard may be bent. Raise the

lower guard with the retracting handle and

make sure it moves freely and does not touch

the blade or any other part, in all angles and

depths of cut.

b) Check the operation of the lower guard

spring. If the guard and the spring are not

operating properly, they must be serviced

before use. Lower guard may operate

sluggishly due to damaged parts, gummy

deposits, or a build-up of debris.

c) Lower guard should be retracted manually

only for special cuts such as “plunge cuts”

and “compound cuts.” Raise lower guard

by retracting handle and as soon as blade

enters the material, the lower guard must

be released. For all other sawing, the lower

guard should operate automatically.

d) Always observe that the lower guard is

covering the blade before placing saw down

on bench or floor. An unprotected, coasting

blade will cause the saw to walk backwards,

cutting whatever is in its path. Be aware of the

time it takes for the blade to stop after switch

is released.

Before using the circular saw

Check the following points:

Does the voltage of the motor correspond •

with the mains voltage (appliances for a

mains voltage of 230 V

Are the mains lead and the mains plug in •

a good condition: solid, without any loose

ends or damage;

Is the saw blade missing any teeth or •

showing any cracks, it so must be

replaced immediately.

Make sure the blade is secure.•

Use this circular saw to saw only wood, •

wood-like products.

Do not use circular saw blades wich are •

deformed or damaged.

Do not use HSS blades.•

Only use blades meeting the required •

dimensions, as well as data and descriptions;

Never apply any blades of which the thick-•

ness is greater than that of the riving knife.

Do not stop the blade of a circular saw by •

pressing the blade from the side.

Check that the blade guard can freely move •

and fully closes.

Never lock-up the guard in the open position.•

Never put sideward pressure on the blade. •

This may cause the blade to break.

Be careful when cutting wood with knots, •

nails or cracks in it and/or dirt on it, as these

can cause the blade to get stuck.

Never leave the circular saw unattended.•

Use this circular saw to saw only wood or •

wood-like products.

Using the machine

Use clamps or a vice to hold the work.•

Never remove wood chips and saw dust that •

is close to the saw blade with your hands. If

there are small pieces of wood left between

the fixed and the movable parts, the circular

saw will have to be stopped. The plug needs

to be removed from the socket, before any left

piece can be removed.

Check that the blade is suitable for the •

spindle speed of the circular saw. Do not

attempt to cut before the circular saw has

reached full speed. Make sure the circular

saw runs without load (i.e. is not in contact

with the work) when you switch it on. The

circular saw must have reached its full speed

first.

Never cut wood that is thicker than the depth •

of the saw blade.

When cutting in wooden walls or floors, check •

there is no wiring or piping where you intend

to cut.

Switch off the tool and wait until the blade has •

stopped completely before moving the saw

away from the work or putting it down.

Hearing protection should be worn when

using circular saw.

Switch off the machine immediately when you

discover:

A defective mains plug or mains lead;•

A defective switch.•

Overheating of the circular saw.•

Smoke or odeur caused by scorched •

insulation.

Electrical safety

When using electric machines always observe

the safety regulations applicable in your country

to reduce the risk of fire, electric shock and

personal injury. Read the following safety

instructions and also the enclosed safety

instructions. Keep these instructions in a safe

place!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CSM1030 - FKS-185 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info