Bedienungsanleitung Ferm CSM1035 (Seite 8 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

763368

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

a cut for any reason, release the trigger and

hold the saw motionless in the material until

the blade comes to a complete stop. Never

attempt to remove the saw from the work or

pull the saw backward while the blade is in

motion or kickback may occur. Investigate and

take corrective actions to eliminate the cause

of blade binding.

c) When restarting a saw in the workpiece,

centre the saw blade in the kerf and check

that saw teeth are not engaged into the

material. If saw blade is binding, it may walk

up or kickback from the workpiece as the saw

is restarted.

d) Support large panels to minimise the risk of

blade pinching and kickback. Large panels

tend to sag under their own weight. Supports

must be placed under the panel on both sides,

near the line of cut and near the edge of the

panel.

e) Do not use dull or damaged blades.

Unsharpened or improperly set blades

produce narrow kerf causing excessive

friction, blade binding and kickback.

f) Blade depth and bevel adjusting locking

levers must be tight and secure before making

cut. If blade adjustment shifts while cutting, it

may cause binding and kickback.

g) Use extra caution when making a “plunge

cut” into existing walls or other blind areas.

The protruding blade may cut objects that can

cause kickback.

Safety instructions guard

a) Check guard for proper closing before each

use. Do not operate the saw if guard does not

move freely and enclose the blade instantly.

Never clamp or tie the guard with the blade

exposed. If saw is accidentally dropped, guard

may be bent. Check to make sure that guard

moves freely and does not touch the blade or

any other part, in all angles and depths of cut.

b) Check the operation and condition of the

guard return spring. If the guard and the

spring are not operating properly, they must

be serviced before use. Guard may operate

sluggishly due to damaged parts, gummy

deposits, or a build-up of debris.

c) Assure that the guide plate of the saw will not

shift while performing the “plunge cut” when

the blade bevel setting is not at 90°. Blade

shifting sideways will cause binding and likely

kick back.

d) Always observe that the guard is covering the

blade before placing saw down on bench or

floor. An unprotected, coasting blade will cause

the saw to walk backwards, cutting whatever is

in its path. Be aware of the time it takes for the

blade to stop after switch is released.

Specific safety instructions

Do not use misshaped or cracked blades.•

Regularly check the blades for damage. If •

necessary, replace them.

Only use blades recommended by Ferm.•

Never use a saw that has components •

missing or a saw that is fitted with accessories

which were not supplied with the saw or which

are not recommended for use with the saw.

Never exert sideways pressure on the blade •

to bring it to a stop.

Remove the plug from the plug socket before •

checking whether the protective cover can

move freely and does not become stuck.

Do not lock or clamp the protective cover.•

Do not use the saw without the protective cover.•

Before using the saw, check whether the •

protective cover has been fitted.

Always remove the plug from the plug socket •

before removing the protective cover,

replacing the blade or when checking the saw

and carrying out maintenance work.

A damaged power cord should only be replaced •

by the manufacturer or a service agent.

After use, the saw must be stored in such a •

way that the blade cannot become damaged.

• Do not use abbrasive discs .

Be careful at all times!

Immediately switch off the machine when:

The plug or power cord is defective or damaged.•

The switch is defective.•

You smell smoke or burning insulation•

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Always check that the power supply

corresponds to the voltage on the rating plate.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CSM1035 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info