Bedienungsanleitung Ferm CSM1039 (Seite 5 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

697752

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

g) Use extra caution when making a “plunge

cut” into existing walls or other blind areas.

The protruding blade may cut objects that can

cause kickback.

Safety instructions lower guard

a) Check lower guard for proper closing before

each use. Do not operate the saw if lower

guard does not move freely and close instantly.

Never clamp or tie the lower guard into the

open position. If saw is accidentally dropped,

lower guard may be bent. Raise the lower

guard with the retracting handle and make sure

it moves freely and does not touch the blade or

any other part, in all angles and depths of cut.

b) Check the operation of the lower guard spring.

If the guard and the spring are not operating

properly, they must be serviced before use.

Lower guard may operate sluggishly due to

damaged parts, gummy deposits, or a build-

up of debris.

c) Lower guard should be retracted manually

only for special cuts such as “plunge cuts”

and “compound cuts.” Raise lower guard by

retracting handle and as soon as blade enters

the material, the lower guard must be released.

For all other sawing, the lower guard should

operate automatically.

) Always observe that the lower guard is covering

the blade before placing saw down on bench or

floor. An unprotected, coasting blade will cause

the saw to walk backwards, cutting whatever is

in its path. Be aware of the time it takes for the

blade to stop after switch is released.

Before using the circular saw

Check the following points:

• Does the voltage of the motor correspond

with the mains voltage (appliances for a

mains voltage of 230 V

• Are the mains lead and the mains plug in

a good condition: solid, without any loose

ends or damage;

• Is the saw blade missing any teeth or

showing any cracks, it so must be replaced

immediately.

• Make sure the blade is secure.

• Use this circular saw to saw only wood,

wood-like products.

• Do not use circular saw blades wich are

deformed or damaged.

• Do not use HSS blades.

• Only use blades meeting the required

dimensions, as well as data and descriptions;

• Never apply any blades of which the thick ness

is greater than that of the riving knife.

• Do not stop the blade of a circular saw by

pressing the blade from the side.

• Check that the blade guard can freely move

and fully closes.

• Never lock-up the guard in the open position.

• Never put sideward pressure on the blade.

This may cause the blade to break.

• Be careful when cutting wood with knots, nails

or cracks in it and/or dirt on it, as these can

cause the blade to get stuck.

• Never leave the circular saw unattended.

• Use this circular saw to saw only wood or

wood-like products.

Using the machine

• Use clamps or a vice to hold the work.

• Only use saw blades that match the

specifications given in this operating manual

and that have been tested and marked in

accordance with EN 847-1.

• Never remove wood chips and saw dust that is

close to the saw blade with your hands. If there

are small pieces of wood left between the

fixed and the movable parts, the circular saw

will have to be stopped. The plug needs to be

removed from the socket, before any left piece

can be removed.

• Check that the blade is suitable for the spindle

speed of the circular saw. Do not attempt

to cut before the circular saw has reached

full speed. Make sure the circular saw runs

without load (i.e. is not in contact with the

work) when you switch it on. The circular saw

must have reached its full speed first.

• Never cut wood that is thicker than the depth

of the saw blade.

• When cutting in wooden walls or floors, check

there is no wiring or piping where you intend to

cut.

• Switch off the tool and wait until the blade has

stopped completely before moving the saw

away from the work or putting it down. Hearing

protection should be worn when using circular

saw.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CSM1039 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info