Bedienungsanleitung Ferm CSM1043 (Seite 9 von 140) (Alle Sprachen)

762265

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

Kickback and related warnings

a) Maintain a firm grip on the power tool and

position your body and arm to allow you to resist

kickback forces. Always use auxiliary handle, if

provided, for maximum control over kickback

or torque reaction during start-up. The operator

can control torque reactions or kickback forces, if

proper precautions are taken.

b) Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

c) Do not position your body in line with the rotating

wheel. Kickback will propel the tool in direction

opposite to the wheel’s movement at the point of

snagging.

d) Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing

have a tendency to snag the rotating accessory

and cause loss of control or kickback.

e) Do not attach a saw chain, woodcarving blade,

segmented diamond wheel with a peripheral

gap greater than 10 mm or toothed saw blade.

Such blades create frequent kickback and loss of

control.

f) Do not “jam” the wheel or apply excessive

pressure. Do not attempt to make an excessive

depth of cut. Overstressing the wheel increases

the loading and susceptibility to twisting or

binding of the wheel in the cut and the possibility

of kickback or wheel breakage.

g) When wheel is binding or when interrupting a cut

for any reason, switch off the power tool and hold

the power tool motionless until the wheel comes

to a complete stop. Never attempt to remove the

wheel from the cut while the wheel is in motion

otherwise kickback may occur. Investigate and

take corrective action to eliminate the cause of

wheel binding.

h) Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully re-enter the cut. The wheel may bind,

walk up or kickback if the power tool is restarted

in the workpiece.

i) Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own

weight. Supports must be placed under the

workpiece near the line of cut and near the edge

of the workpiece on both sides of the wheel.

j) Use extra caution when making a “pocket cut”

into existing walls or other blind areas. The

protruding wheel may cut gas or water pipes,

electrical wiring or objects that can cause

kickback.

Be careful at all times!

Immediately switch off the machine when:

• The plug or power cord is defective or

damaged.

• The switch is defective.

• You smell smoke or burning insulation

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Always check that the power supply

corresponds to the voltage on the rating

plate.

Class ll machine. Your machine is double

insulated; therefore no earthwire is

required.

If the replacement of the supply cord is necessary,

this has to be done by the manufacturer or his

agent in order to avoid a safety hazard.

Using extension cables

Only use an approved extension cable suitable

for the power input of the machine. The minimum

conductor size is 1.5 mm2. When using a cable

reel always unwind the reel completely.

3. ASSEMBLY

Before assembly, always switch off the

machine and remove the mains plug

from the mains.

Mounting the handle

Fig. 2

• Mount the handle (2) to the metal part on the

machine as shown in Fig. 2.

• Fix the Cap nut (11) tightly using a wrench.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CSM1043 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info