Bedienungsanleitung Ferm CSM1043 (Seite 10 von 140) (Alle Sprachen)

762265

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

Attachment of the parallel guide

Fig. 3

• Attach the parallel guide (12) on the right side

of the machine, as shown in Fig. 3

• Lock the guide down by turning the

adjustment knob (13) clockwise.

4. OPERATION

Unplug the machine before mounting

any accessories!

Adjusting the sawing depth

Fig. 1, 5

The sawing depth can be adjusted with the saw

depth limiter.

• Loosen the saw depth limiter (3) using the hex

key (17) and move the saw depth limiter to the

required saw depth. The sawing depth ‘A’ is

shown in Fig. 5B. The depth indicator has long

lines to indicate even milimeters and short

lines to indicate odd milimeters.

• Tighten the saw depth limiter (3) using the hex

key (17).

Indications:

• For optimal result when sawing wood, the

cutting depth should be set slightly greater

than the thickness of the chosen material.

• When cutting plastic, the cutting depth should

also be greater than the thickness of the

material. If the material begins to melt, then

setting a greater depth of cut usually resolves

the problem.

• When cutting metal, the cutting depth should

be at least 1.0 mm larger than the thickness of

the material.

• When sawing wood or plastic, the depth of cut

can also be set exactly on the thickness of the

material to prevent that the underlying surface

gets damaged. However, this does lead to an

impure saw cut at the bottom of the workpiece

Blade replacement without removing the guard

Fig. 4

Incorrect positioning of the blade can

permanently damage the tool. Always

wear protective gloves to prevent injury!

1. Press the spindle lock button (14) to prevent

the saw from turning. (Fig. 4A)

2. Keep the spindle lock button (14) pressed and

loosen the clamping nut (16) using the hex key

(17). (Fig. 4B)

3. Remove the mounting flange (15)

4. Loosen the saw depth limiter (3) using the hex

key (17) and press the guard to remove the

blade. (Fig. 4C)

5. Keep the guard pressed and place the new

blade onto the blade shaft. Ensure the hole

locates correctly and the teeth point in the

direction of the curved arrow. (Fig. 4C)

6. Place the mounting flange (15) insuring the

long sides of the mounting flange correspond

with the long sides of the blade shaft.

7. Press the spindle lock button (14) pressed and

tighten the clamping nut (16) using the hex key

(17). (Fig. 4D)

8. Make sure the blade rotates smoothly by

rotating the sawblade at least one turn. Check

if the guard functions correctly.

9. The machine can now be used again.

Holding and turning on the saw

Fig. 1

Holding the saw correctly makes the work lighter,

cleaner and safer.The Precision Circular Saw is

only suitable for right-handed use.

• Slide the on-/off switch (4) forward.

• Release the on-/off switch to switch the

machine off

Speed Adjustment

Fig. 1

The required speed can be adjusted by using the

Speed adjustment knob (7). Also during running

the rotational speed can be adjusted.

• To increase the speed, turn the Speed

adjustment knob (7) clockwise.

• To decrease the speed, turn the Speed

adjustment knob (7) anti-clockwise.

The required speeds depends on the material

and can be determined by practical testing.

Clamping

It is not normally necessary to clamp the material

being cut as long as it is fully supported on a work

surface and held with one hand. Clamping should

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CSM1043 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info