Bedienungsanleitung Ferm CSM1051 (Seite 13 von 56) (Deutsch, Englisch, Holländisch, Französisch)

798918

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

oil on the joints and on the tooth tips of the

individual chain links.

1. The chain should be well-tensioned to ensure

proper sharpening.

2. For the sharpening, a round file with 4.0 mm

diameter is necessary.

Other diameters damage the chain and

can lead to danger during work!

3. Sharpen only from the inside to the outside.

Guide the fi le from the inner side of the cutting

teeth to the outer side. Lift the fi le when you

are withdrawing it.

4. Sharpen first the teeth on one side. Turn the

saw around and sharpen the teeth of the other

side.

5. The chain is worn and must be replaced by

a new saw chain if only approx. 4 mm of the

cutting teeth is remaining.

6. After the sharpening, all cutting elements must

now be equal in length and width.

7. After every third sharpening, the sharpness

depth (depth limitation) must be checked and

the height filed with the aid of a flat file. The

depth limitation should be set back about 0.65

mm from the cutting tooth. After the setting

back of depth limitation, round it off a little at

the front.

Adjusting the chain tension

The adjustment of the chain tension is described

in the chapter “Assembly - tensioning chainsaw”.

• Switch off the device and remove the battery

(14) from the device.

• Check the chain tension regularly and re-

adjust this as often as possible. When the saw

chain is tensioned with 9 N (approx. 1 kg), the

gap between the saw chain and the guide rail

may not be more than 2 mm.

Starting up a new saw chain

In the case of a new chain, the tensioning force

decreases after some time. Therefore, you have

to re-tension the chain after the first 5 cuts and no

later than after 10 minutes’ sawing time.

Never attach a new chain to a worn drive pinion

or place onto a damaged or worn chain bar. The

chain could spring back or break, potentially

leading to serious injury.

Maintaining the chain bar

Use cut-protection gloves when

handling the chain or the chain bar.

1. Switch off the device and remove the battery

(14) from the device.

2. Remove the sprocket chain wheel covering (9),

the saw chain (12) and the chain bar (11).

3. Check the chain bar (11) for wear. Remove

burrs and straighten the guide surfaces with a

flat file.

4. Mount chain bar (11), chainsaw (12) and

sprocket chain wheel covering (9) and tighten

the saw chain.

Turning the blade bar

Use cut-resistant gloves when working

with the saw chain or with the blade bar.

The blade bar (11) needs to be reversed regularly

after a working time of about 10 hours in order to

ensure even wear.

1. Switch off the device and remove the battery

(14) from the device.

2. Remove the sprocket cover (9), saw chain (12)

and blade bar (11).

3. Turn the blade bar around its horizontal

axis and install the blade bar and chain as

described under “Installing the saw chain and

blade bar”.

When doing so, pay attention to the correct

rotation direction of the saw chain!

Direction of travel of saw

chain

Use the graphical symbol above the chain

sprocket (17) as a guide to align the saw chain

(12) when the blade bar is rotated. The illustrated

direction of travel on the blade bar is no longer

true.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CSM1051 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info