Bedienungsanleitung Ferm CTM1018 (Seite 7 von 52) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

763693

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

a) Maintain a firm grip on the power tool and

position your body and arm to allow you

to resist kickback forces. The operator can

control kickback forces, if proper precautions

are taken.

b) Use special care when working corners,

sharp edges etc. Avoid bouncing and

snagging the accessory. Corners, sharp

edges or bouncing have a tendency to snag the

rotating accessory and cause loss of control or

kickback.

c) Do not attach a toothed saw blade. Such

blades create frequent kickback and loss of

control.

d) Always feed the bit into the material in

the same direction as the cutting edge is

exiting from the material (which is the same

direction as the chips are thrown). Feeding

the tool in the wrong direction causes the

cutting edge of the bit to climb out of the work

and pull the tool in the direction of this feed.

e) When using rotary files, cut-off wheels,

high-speed cutters or tungsten carbide

cutters, always have the work securely

clamped. These wheels will grab if they

become slightly canted in the groove, and can

kickback. When a cut-off wheel grabs, the

wheel itself usually breaks. When a rotary file,

high-speed cutter or tungsten carbide cutter

grabs, it may jump from the groove and you

could lose control of the tool.

Additional safety instructions for

grinding and cutting-off operations

Safety warnings specific for grinding and

abrasive cutting-off operations:

a) Use only wheel types that are recommended

for your power tool and only for

recommended applications. For example:

do not grind with the side of a cut-off wheel.

Abrasive cut-off wheels are intended for

peripheral grinding, side forces applied to these

wheels may cause them to shatter.

For threaded abrasive cones and plugs

use only undamaged wheel mandrels with

an unrelieved shoulder flange that are of

correct size and length. Proper mandrels will

reduce the possibility of breakage

c) Do not “jam” a cut-off wheel or apply

excessive pressure. Do not attempt to make

an excessive depth of cut. Overstressing the

wheel increases the loading and susceptibility to

twisting or snagging of the wheel in the cut and

the possibility of kickback or wheel breakage.

d) Do not position your hand in line with and

behind the rotating wheel. When the wheel,

at the point of operation, is moving away from

your hand, the possible kickback may propel the

spinning wheel and the power tool directly at

you.

e) When wheel is pinched, snagged or when

interrupting a cut for any reason, switch

off the power tool and hold the power tool

motionless until the wheel comes to a

complete stop. Never attempt to remove

the cut-off wheel from the cut while the

wheel is in motion otherwise kickback may

occur. Investigate and take corrective action

to eliminate the cause of wheel pinching or

snagging.

f) Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed

and carefully re-enter the cut. The wheel may

bind, walk up or kickback if the power tool is

restarted in the workpiece.

g) Support panels or any oversized workpiece

to minimize the risk of wheel pinching and

kickback. Large workpieces tend to sag under

their own weight. Supports must be placed

under the workpiece near the line of cut and

near the edge of the workpiece on both sides of

the wheel.

h) Use extra caution when making a “pocket

cut” into existing walls or other blind areas.

The protruding wheel may cut gas or water

pipes, electrical wiring or objects that can

cause kickback.

Additional safety instructions for wire

brushing operations

Safety warnings specific for wire brushing

operations:

a) Be aware that wire bristles are thrown by

the brush even during ordinary operation.

Do not overstress the wires by applying

excessive load to the brush. The wire bristles

can easily penetrate light clothing and/or skin.

b) Allow brushes to run at operating speed

for at least one minute before using them.

During this time no one is to stand in front or

in line with the brush. Loose bristles or wires

will be discharged during the run-in time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CTM1018 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info