Bedienungsanleitung Ferm CTM1018 (Seite 9 von 52) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

763693

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Vibration level

The vibration emission level stated in this

instruction manual has been measured in

accordance with a standardised test given in EN

60745; it may be used to compare one tool

with another and as a preliminary assessment of

exposure to vibration when using the tool for the

applications mentioned.

- using the tool for different applications, or with

different or poorly maintainted accessories,

may significantly increase the exposure level.

- the times when the tool is switched off or when

it is running but not actually doing the job, may

significantly reduce the exposure level.

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work

patterns.

Description

The numbers in the following text refer to the

pictures on page 2-3

1. Collet chuck

2. LED work light

3. Spindle lock

4A. Speed adjustment button “+”

4B. Speed adjustment button “-“

5. On/off button

6. Speed indication lights

7. Charger indication light

8. Chuck spanner

3. ASSEMBLY

Always make sure the machine is turned

off before mounting an accessory.

Warning! Change accessories by

inserting an accessory into the collet (or

chuck) as far possible to minimize run out

and unbalance.

Assembly of accessories

Fig. 2

Press down the spindle lock (3) and hold it down.

Using the chuck spanner (8) you can undo the

collet chuck (1). Put the accessory in its place.

Hold down the spindle lock when you fasten the

collet chuck with the chuck spanner.

Do not press the spindle lock button

while the motor is running.

4. OPERATION

Switch on the machine by pressing the on/off

button (5).

With the speed adjustment button “+”(4A)

or “-“(4B) you can regulate the speed of the

Combitool. Do not put the machine down when

the motor is still running. Do not place the

machine on a dusty surface. Dust particles may

enter the mechanism.

Too high a load at a low speed of the

Combitool can burn out the engine.

The battery must be charged before first use.

Charging the device (with the charger)

• Plug the charger plug into an electrical outlet

and wait for a while. The charger indication

light (7) will lighten up and show the charging

status.

LED Charger status

Red Battery charging in progress

Green Battery charging finished, battery fully charged

• After the battery is fully charged remove the

charger plug from the outlet and remove the

small plug from the device.

Holding and guiding the tool

Fig. 3

• For precision work (engraving): pencil grip (A)

• For rough work (grinding): paring knife hand

grip (B)

• When you need to keep the tool parallel to the

work surface (e.g. using a cut-off wheel): 2

hand golf grip (C)

Optimal use of the combi tool and its

accessories

Fig. 1

For optimal use of the accessories use the

correct speed. You can refer to the overview

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CTM1018 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info