Bedienungsanleitung Ferm FBF 1200 (Seite 8 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch)

78982

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

the thumbwheel (13). Also during running the

rotational speed can be adjusted.

1 - 2 = low speed

3 - 4 = medium speed

5 - 6 = high speed

Max = maximum speed

The required speed depends of the material

and can be determined by practical testing.

Furthermore router bits with a large diameter

need a lower rotational speed.

Material Diameter Speed stages

router bit

Hardwood > 20 mm 1 - 2

10 - 20 mm 3 - 4

< 10 mm 5 - max

Softwood > 20 mm 1 - 3

10 - 20 mm 3 - 6

< 10 mm 5 - max

Aluminium > 15 mm 1

< 15 mm 1 - 2

Plastic > 15 mm 1 - 2

< 15 mm 2 - 3

After longer periods of working at low speed, allow

the machine to cool down by running it for a few

minutes at high speed with no load.

Height setting of the router column

Fig. G

Button (14) is used to set the maximum height of

the router.

The cutting depth is then fixed. This is usually

necessary when using the tool on a special router

table.

Rough setting:

Loosen the clamping lever (11). The router •

can then be pushed down against the spring

force.

Hold button (14) between your thumb and •

index finger.

Push the grey button (14) and use your other •

hand to push the router down at the same time.

Release the button. The router is now locked •

and will no longer return to its original position.

Fine adjustment:

Turn button (14) clockwise. This causes the •

router column to slowly move down.

Turn button (14) counter-clockwise. This •

causes the router column to slowly move up.

Setting of the cutting depth

Fig. G

The cutting depth can be adjusted by using

buttons 8, 9, 11 and 15. If the cutting depth is set

correctly, the groove in question can be routed

accurately to within 0.1 mm.

Preparation:

Place the desired cutter in the tool.•

Loosen the clamping lever (11). The router can •

then be pushed down against the spring force.

Push the tool down until the cutter touches the •

workpiece, then relock it using the clamping

lever (11).

Loosen button 9 (counter-clockwise).•

Set button 15 to zero.•

Use button 8 to set the depth all the way •

down.

Tighten button 9 (clockwise). The cutting •

depth is now set to precisely 0 mm.

Rough setting:

Read the value from the scale (12).•

Loosen button 9 (counter-clockwise).•

Turn button 8 and re-read the value from the •

scale. The difference between the two values

is the cutting depth setting.

For example: If the value on the scale (12)

is 8.5 in the zero-setting and the value is 7.0

after button (8) has been turned, then the

cutting depth has been set to 1.5 cm.

Retighten button 9 (clockwise).•

Fine adjustment:

Loosen button 9 (counter-clockwise).•

The top button (15) is still set to zero. Give this •

button a full counter-clockwise turn, until it is

back in the zero position. The cutting depth is

now 1.0 mm less.

If required, the cutting depth can be set •

accurately to within 0.1 mm.

Retighten button 9.•

Adjustment using the revolver- depth stop

The revolver-depth stop enables you to quickly

choose between six different cutting depths.

These are also determined by the adjustment of

the depth stop (10).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm FBF 1200 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info