Bedienungsanleitung Ferm FDAG 750 (Seite 5 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

79094

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Ferm

The speed of the machine must not exceed the

value on the grinding disc.

Make sure that the dimensions of the grinding •

disc correspond to the specifications of the

machine.

Make sure that the grinding disc has been •

mounted and fastened properly. Do not use

reducing rings or adapters to make the grinding

disc fit properly.

Treat and store grinding discs in conformance •

with the supplier’s instructions.

Do not use the machine for grinding •

workpieces with a maximum thickness

exceeding the maximum grinding depth of the

grinding disc.

Do not use grinding discs for deburring.•

When grinding discs have to be mounted on •

the thread of the spindle, make sure that the

spindle has sufficient thread. Make sure that

the spindle is sufficiently protected and does

not touch the grinding surface.

Before use, inspect the grinding disc for any •

damage. Do not use grinding discs which are

cracked, ripped or otherwise damaged.

Before use, let the machine run idle for 30 •

seconds. Immediately switch off the machine in

case of abnormal vibrations or occurrence of

another defect. Carefully inspect the machine

and grinding disc before switching the machine

on again.

Make sure that sparks do not put people into •

danger or that they contact highly flammable

substances.

Make sure that the workpiece is sufficiently •

supported or clamped. Keep your hands away

from the surface to be cut.

Always wear safety goggles and hearing •

protection. If desired or required also use

another kind of protection like for example an

apron or helmet.

Ensure that mounted wheels and points are •

fitted in accordance with the manufacturer’s

instructions.

Ensure that blotters are used when they are •

provided with the bonded abrasive product and

when they are required.

If a guard is supplied with the tool never use •

the tool without such a guard.

For tools intended to be fitted with threaded •

hole wheel, ensure that the thread in the wheel

is long enough to accept the spindle length.

Ensure that ventilation openings are kept clear •

when working in dusty conditions. If it should

become nessesary to clear dust, first

disconnect the tool from the mains supply (use

non metallic objects) and avoid damaging

internal parts.

Though poor conditions of the electrical mains, •

shortly voltage drops can appear when starting

the equipment. This can influence other

equipment (eq. blinking of a lamp). If the

mains-impedance Zmax <0.348 Ohm, such

disturbances are not expected. (In case of

need, you may contact your local supply

authority for further information.

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Always check that the power supply

corresponds to the voltage on the rating

plate.

Your machine is double insulated;

therefore no earthwire is required.

Replacing cables or plugs

Immediately throw away old cables or plugs when

they have been replaced by new ones. It is

dangerous to insert the plug of a loose cable in the

wall outlet.

Using extension cables

Only use an approved extension cable suitable for

the power input of the machine. The minimum

conductor size is 1,5 mm

. When using a cable

reel always unwind the reel completely.

3. ASSEMBLY

Prior to mounting an accessory always

unplug the tool.

Mounting the side-handle

Fig. 1

The side handle can be used for both left-hand

and right-hand control.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm FDAG 750 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info