Bedienungsanleitung Ferm FDAG 880 (Seite 7 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Norwegisch)

78516

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

Mains plug replacement (UK only)

If the moulded 3-pin plug attached to the unit is

damaged and needs replacing, it is important that

it is correctly destroyed and replaced by an

approved BS 1363/5A fused plug and that the

following wiring instructions are followed.

The wires in the mains cable are coloured in

accordance with the following code:

blue neutral

brown live

As the colours of the wires in the mains cable of

the unit may not correspond to the coloured

markings identifying the terminals in the plug,

proceed as follows:

- The wire which is coloured blue must be

connected to the terminal which is marked with

the letter N or coloured black.

- The wire which is coloured brown must be

connected to the terminal which is marked with

the letter L or coloured red.

TECHNICAL DATA

AGM1043

Mains voltage V~ 230

Mains frequency Hz 50

Power input W 880

No-load speed min

-1

11,000

Grinding disc

Diameter mm 125

Bore mm 22.2

Spindle thread M14

Weight kg 2.2

NOISE AND VIBRATION

AGM1043

Sound pressure (L

) dB(A) 87.7

Acoustic power (L

) dB(A) 98.7

Uncertainty (K) dB(A) 3

Vibration m/s

7.52

Uncertainty (K) m/s

1.5

Wear hearing protection.

Vibration level

The vibration emission level stated in this instruction

manual has been measured in accordance with a

standardised test given in EN 60745; it may be used

to compare one tool with another and as a

preliminary assessment of exposure to vibration

when using the tool for the applications mentioned

- using the tool for different applications, or with

different or poorly maintainted accessories,

may signicantly increase the exposure level

- the times when the tool is switched off or when

it is running but not actually doing the job, may

signicantly reduce the exposure level

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work

patterns

DESCRIPTION (FIG. A)

Your angle grinder has been designed for grinding

and cutting masonry and steel.

1. On/off switch

2. On/off switch lock

3. Spindle lock button

4. Spindle

5. Guard

6. Main grip

7. Auxiliary grip

8. Carbon brush indicator

ASSEMBLY

Before assembly, always switch off the

machine and remove the mains plug

from the mains.

Mounting and removing the grinding disc



Never attempt to remove the guard.

Mounting

● Place the machine on a table with the guard

(5) facing upwards.

● Mount the spacer (9) onto the spindle (4).

● Mount the grinding disc (10) onto the spindle (4).

● Keep the spindle lock button (3) pressed and

rmly tighten the tension nut (11) using the

spanner (12).

Removing

● Place the machine on a table with the guard

(5) facing upwards.

● Keep the spindle lock button (3) pressed and

loosen the tension nut (11) using the spanner

(12).

● Remove the grinding disc (10) from the spindle

(4).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm FDAG 880 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info