Bedienungsanleitung Ferm FDPD 710 (Seite 5 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

78861

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

● Never put the machine down on a table or

a workbench before it has been switched off.

Electrical safety

Always check that the voltage of the

power supply corresponds to the voltage

on the rating plate.

● Do not use the machine if the mains cable or

the mains plug is damaged.

● Only use extension cables that are suitable for

the power rating of the machine with

a minimum thickness of 1.5 mm

. If you use

a extension cable reel, always fully unroll the

cable.

Mains plug replacement (UK only)

If the moulded 3-pin plug attached to the unit is

damaged and needs replacing, it is important that

it is correctly destroyed and replaced by an

approved BS 1363/5A fused plug and that the

following wiring instructions are followed.

The wires in the mains cable are coloured in

accordance with the following code:

blue neutral

brown live

As the colours of the wires in the mains cable of

the unit may not correspond to the coloured

markings identifying the terminals in the plug,

proceed as follows:

- The wire which is coloured blue must be

connected to the terminal which is marked with

the letter N or coloured black.

- The wire which is coloured brown must be

connected to the terminal which is marked with

the letter L or coloured red.

TECHNICAL DATA

PDM1027

Mains voltage V~ 230

Mains frequency Hz 50

Power input W 710

No-load speed min

-1

0 - 2,700

Impact rate min

-1

0 - 43,200

Max. drill bit diameter

Wood mm 25

Concrete mm 13

Steel mm 10

Protection class IP 20

Weight kg 1.9

NOISE AND VIBRATION

PDM1027

Sound pressure (L

) dB(A) 91

Acoustic power (L

) dB(A) 102

Uncertainty (K) dB(A) 3

Vibration

Metal m/s

14.27

Concrete m/s

3.50

Uncertainty (K) m/s

1.5

Wear hearing protection.

Vibration level

The vibration emission level stated in this instruction

manual has been measured in accordance with a

standardised test given in EN 60745; it may be used

to compare one tool with another and as a

preliminary assessment of exposure to vibration

when using the tool for the applications mentioned

- using the tool for different applications, or with

different or poorly maintainted accessories,

may signicantly increase the exposure level

- the times when the tool is switched off or when

it is running but not actually doing the job, may

signicantly reduce the exposure level

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work

patterns

DESCRIPTION (FIG. A)

Your impact drill has been designed for drilling

holes in wood, metal and plastics and for hammer

drilling in brick and concrete.

1. On/off switch

2. Lock-on button

3. Speed adjustment wheel

4. Forward/reverse switch

5. Switch for drilling / hammer drilling

6. Chuck

7. Main grip

8. Auxiliary grip

9. Depth stop

10. Storage system (drill bits)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm FDPD 710 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info