Bedienungsanleitung Ferm FDS 220 K (Seite 6 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Norwegisch)

78494

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

Mains plug replacement (UK only)

If the moulded 3-pin plug attached to the unit is

damaged and needs replacing, it is important that

it is correctly destroyed and replaced by an

approved BS 1363/3A fused plug and that the

following wiring instructions are followed.

The wires in the mains cable are coloured in

accordance with the following code:

blue neutral

brown live

As the colours of the wires in the mains cable of

the unit may not correspond to the coloured

markings identifying the terminals in the plug,

proceed as follows:

- The wire which is coloured blue must be

connected to the terminal which is marked with

the letter N or coloured black.

- The wire which is coloured brown must be

connected to the terminal which is marked with

the letter L or coloured red.

TECHNICAL DATA

PSM1013

Mains voltage V~ 230

Mains frequency Hz 50

Power input W 220

No-load speed min

-1

13,000

Protection class IP 20

Weight kg 1.25

NOISE AND VIBRATION

PSM1013

Sound pressure (L

) dB(A) 76.0

Acoustic power (L

) dB(A) 87.0

Uncertainty (K) dB(A) 3

Vibration m/s

1.24

Uncertainty (K) m/s

1.5

Wear hearing protection.

Vibration level

The vibration emission level stated in this instruction

manual has been measured in accordance with a

standardised test given in EN 60745; it may be used

to compare one tool with another and as a

preliminary assessment of exposure to vibration

when using the tool for the applications mentioned

- using the tool for different applications, or with

different or poorly maintainted accessories,

may signicantly increase the exposure level

- the times when the tool is switched off or when

it is running but not actually doing the job, may

signicantly reduce the exposure level

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work

patterns

DESCRIPTION (FIG. A)

Your delta sander has been designed for sanding

wood, metal, plastics and painted surfaces.

1. On/off switch

2. Sanding pad

3. Grip

4. Dustbag connection

ASSEMBLY

Before assembly, always switch off the

machine and remove the mains plug

from the mains.

Mounting and removing the sanding paper



Mounting

● Mount sanding paper (5) with the required

grain size onto the sanding pad (2). Make sure

that the perforation in the sanding paper (5)

corresponds with the perforation on the sanding

pad (2).

- Use coarse sanding paper (grain 50) for

sanding rough, uneven surfaces.

- Use medium sanding paper (grain 80) for

removing the remaining scratches from the

coarse sanding paper.

- Use ne sanding paper (grain 120) for

nishing surfaces.

Removing

● Remove the sanding paper (5) from the

sanding pad (2).

USE



● To switch on the machine, set the on/off switch

(1) to the ‘I‘ position.

● To switch off the machine, set the on/off switch

(1) to the ‘0‘ position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm FDS 220 K Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info