• Use this circular saw to saw only wood, wood-like
products.
• Do not use circular saw blades wich are deformed or
damaged.
• Do not use HSS blades.
• Only use blades meeting the required dimensions, as
well as data and descriptions;
Never apply any blades of which the thickness is
greater than that of the riving knife.
• Do not stop the blade of a circular saw by pressing
the blade from the side.
• Check that the blade guard can freely move and fully
closes.
• Never lock-up the guard in the open position.
• Never put sideward pressure on the blade. This may
cause the blade to break.
• Be careful when cutting wood with knots, nails or
cracks in it and/or dirt on it, as these can cause the
blade to get stuck.
• Never leave the circular saw unattended.
• Use this circular saw to saw only wood or wood-like
products.
SAFETY TIPS FOR THE LASER BEAMER.
• Never look into the light beam of the laser.
• Never point the light beam of the laser at humans or
animals.
• Do not point the light beam of the laser at strongly
reflecting material. Hazard from reflected light.
• Only have repairs made to the laser beamer by
qualified personnel / professional repair specialists.
• Do not insert any hard objects into the laser optics.
• Clean the laser optics with a soft, dry brush.
USING THE MACHINE:
• Use clamps or a vice to hold the work.
• Never remove wood chips and saw dust that is close
to the saw blade with your hands. If there are small
pieces of wood left between the fixed and the
movable parts, the circular saw will have to be
stopped. The plug needs to be removed from the
socket, before any left piece can be removed.
• Check that the blade is suitable for the spindle speed
of the circular saw. Do not attempt to cut before the
circular saw has reached full speed. Make sure the
circular saw runs without load (i.e. is not in contact
with the work) when you switch it on. The circular
saw must have reached its full speed first.
• Never cut wood that is thicker than the depth of the
saw blade.
• When cutting in wooden walls or floors, check there
is no wiring or piping where you intend to cut.
• Switch off the tool and wait until the blade has
stopped completely before moving the saw away
from the work or putting it down. Hearing
protection should be worn when using circular saw.
SWITCH OFF THE MACHINE IMMEDIATELY
WHEN YOU DISCOVER:
• A defective mains plug or mains lead.
• A defective switch.
• Overheating of the circular saw.
• Smoke or odeur caused by scorched insulation.
3. ASSEMBLY AND
ADJUSTING INSTRUCTIONS
Before adjusting the saw, make sure the plug is
removed from the socket.
SETTING THE SAWING ANGLE (BEVEL)
Fig.B
• Loosen both knobs (1).
• Rotate the soleplate to the correct position (0° -
45°), and tighten the knobs. The sawing angle (bevel)
can be read on the protractor (2).
FITTING THE RIP FENCE
Fig.B
• Loosen knob (3).
• Insert the rip fence into the slots provided (4).
• Set the correct cut width and tighten the knob (3).
SETTING THE CUT DEPTH
Fig.A
• Loosen knob (4).
• Move the soleplate (17) downwards.
• The cut depth of the saw blade can be read off on the
side of the safety guard.
• Tighten the clamping knob (4) once the correct
depth is set.
EXCHANGING OR CLEANING THE SAW
BLADE
Fig.D
• Use the shaft locking knob (2) to prevent the shaft
from rotating.
• Next loosen the hexagon screw (3) in the centre of
the saw blade, using the Allen key provided.
• Turn the safety guard to the rear, and hold it there
with the aid of the knob (1).
• Withdraw the retaining ring and the saw blade, and
clean the saw blade, or replace it with a new one.
• Again place the saw blade back on the shaft. Ensure
that the teeth of the saw blade are pointing in the
same direction as the riving knife (4).
• Ensure that the splitting wedge is set in such a way
that
• the gap between it and the toothed wheel rim of the
saw blade does not exceed 5 mm
• and that the toothed wheel does not protrude more
than 5 mm beyond the lower edge of the splitting
wedge.
• The splitting wedge must always be used except
when cutting into the middle of the workpiece.
• Allow the safety guard to return over the saw bla-
de by releasing the knob (1).
• Press the shaft locking knob (2) back in, refit the
retaining ring (5) and tighten the hexagon screw
firmly once more.
REPLACING THE CARBON BRUSHES
Fig.E
• Remove the screws (1).
• Withdraw the carbon brushes (2) from the circular
handsaw and inspect them for wear.
• Place the carbon brushes back in the brush holders
provided.
Ferm 5
• Når De isætter batterierne, sikre Dem at +/-
terminalen er korrekt placeret som vist inde i
batterirummet.
• Check at laser lyset er korrekt lukket ved forsigtigt at
åbne låget opad. Hvis låget åbner, skal De gentage
lukke proceduren indtil låget forbliver korrekt
lukket.
JUSTERING AF LASER LYSET
• Behandling ved transport og ofte brug kan påvirke
laser lysets præcision.
• Laser lyset i sig selv kan let blive justeret.
• Hold bladet af den runde sav mod en lige kant eller
perfekt lige planke.
• Tænd for laser lyset.
• Check om laser lyset løber parallel med kanten eller
plankens kant.
Hvis laser lyset ikke løber parallel, gør da følgende:
• Løs de skrue foran på laseren et par omdrejninger.
• Hold bladet på rundsaven mod en lige kant eller
perfekt lige planke.
• Juster laseren sådan at den løber fuldstændigt lige
med kanten.
• Fastskrue de skrue igen.
FEJL
Hvis rundsaven ikke virker hensigtsmæssigt, kan du
gennemgå følgende mulige årsager og tilhørende
løsninger for at afhjælpe problemerne.
1. Elektromotoren overophedes.
• Motoren overbelastes, fordi der saves for store
arbejdsemner.
Sav i et lavere tempo og lad motoren køle af.
• Motoren er defekt.
Få rundsaven repareret eller set efter hos en
forhandler.
2. Maskinen virker ikke, selv om den er tilkoblet.
• Fejl i netledningen.
Kontrollér netledningen for brud.
• Afbryderen er defekt.
Få rundsaven repareret eller set efter hos en
forhandler.
3. Det er vanskeligt at føre arbejdsemnet i en ret
linie langs savklingen og savskæret er
uregelmæssigt.
• Savklingen er bøjet eller sløv.
Udskift savklingen.
4. Rundsaven støjer og/eller går meget
uregelmæssigt.
• Kulbørsterne er slidte.
Udskiftning af kulbørsterne (Fig. E)
5. VEDLIGEHOLDELSE
Sørg for at maskinen ikke står under strøm, når der
udføres vedligeholdelsesarbejder på mekanikken.
Maskinerne er udviklet til at fungere længe uden
problemer med et minimum af vedligeholdelse. Ved at
rengøre maskinen regelmæssigt og behandle den
korrekt, bidrager De til en længere levetid for maskinen.
Rengøring
Rengør regelmæssigt maskinkappen med en blød klud,
helst efter hvert brug. Sørg for at ventilationshullerne er
fri for støv og snavs. Brug en blød klud, der er vædet i
sæbevand til at fjerne hårdnakket snavs. Brug ingen
opløsningsmidler, så som benzin, alkohol, ammoniak,
osv. Den slags stoffer beskadiger kunststofdelene.
Smøring
Maskinen behøver ingen ekstra smøring.
Fejl
Skulle en fejl opstå, f.eks. pga. slidtage af en enhed,
kontakt venligst serviceadressen på garantibeviset. På
bagsiden af denne manual finder du en tegning med
alle dele, der kan bestilles.
MILJØ
For at undgå transportbeskadigelse leveres maskinen i
en solid emballage. Emballagen er så vidt muligt lavet
af genbrugsmateriale. Genbrug derfor emballagen.
Defekte og/eller kasserede elektriske eller
elektroniske maskiner skal afleveres på en
genbrugsplads.
GARANTI
Læs det separat vedlagte garantikort for
garantibetingelserne
56 Ferm
