Bedienungsanleitung Ferm FKS 185 L (Seite 8 von 62) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Norwegisch)

110130

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

Ferm 117

Rengøring

Rengør regelmæssigt maskinkappen med en blød klud, helst efter hvert brug. Sørg for at

ventilationshullerne er fri for støv og snavs. Brug en blød klud, der er vædet i sæbevand til

at fjerne hårdnakket snavs. Brug ingen opløsningsmidler, så som benzin, alkohol, ammo-

niak, osv. Den slags stoffer beskadiger kunststofdelene.

Udskiftning af kulbørster

Fig. E

• Fjern skruerne (1).

• Træk kulbørsterne (2) ud fra rundsaven og undersøg dem for slitage.

• Sæt kulbørsterne tilbage i de forhåndenværende holdere.

• Kontroller, at kobberkontakten på kulbørsterne er i god kontakt med kobberdelen i

børsteholderen.

• Sæt skruerne (1) i igen og stram dem godt.

Efter mange driftstimer kan kulbørsterne være slidt. Derfor skal kulbørsterne

kontrolleres regelmæssigt efter hver 30 driftstimer. Hvis kulbørsterne er kortere

end 4 mm, skal de udskiftes med nye.

Smøring

Maskinen behøver ingen ekstra smøring.

Fejl

• Elektromotoren over-

ophedes.

• Maskinen virker ikke,

selv om den er tilko-

blet.

• Det er vanskeligt at

føre arbejdsemnet i en

ret linie langs savklin-

gen og savskæret er

uregelmæssigt.

• Rundsaven støjer

og/eller går meget ure-

gelmæssigt.

• Motoren overbelastes,

fordi der saves for

store arbejdsemner.

• Motoren er defekt.

• Fejl i netledningen.

• Afbryderen er defekt.

• Savklingen er bøjet

eller sløv.

• Kulbørsterne er slidte.

• Sav i et lavere tempo

og lad motoren køle af.

• Kontakt venligst serv-

iceadressen på garanti-

beviset.

• Kontrollér netledningen

for brud.

• Kontakt venligst serv-

iceadressen på garanti-

beviset.

• Udskift savklingen.

• Kontakt venligst serv-

iceadressen på garanti-

beviset.

Ferm

d) Support large panels to minimise the risk of blade pinching and kickback. Large panels

tend to sag under their own weight. Supports must be placed under the panel on both

sides, near the line of cut and near the edge of the panel.

e) Do not use dull or damaged blades. Unsharpened or improperly set blades produce

narrow kerf causing excessive friction, blade binding and kickback.

f) Blade depth and bevel adjusting locking levers must be tight and secure before making cut.

If blade adjustment shifts while cutting, it may cause binding and kickback.

g) Use extra caution when making a "plunge cut" into existing walls or other blind areas. The

protruding blade may cut objects that can cause kickback.

Safety instructions lower guard

a) Check lower guard for proper closing before each use. Do not operate the saw if lower

guard does not move freely and close instantly. Never clamp or tie the lower guard into the

open position. If saw is accidentally dropped, lower guard may be bent. Raise the lower

guard with the retracting handle and make sure it moves freely and does not touch the

blade or any other part, in all angles and depths of cut.

b) Check the operation of the lower guard spring. If the guard and the spring are not operating

properly, they must be serviced before use. Lower guard may operate sluggishly due to

damaged parts, gummy deposits, or a build-up of debris.

c) Lower guard should be retracted manually only for special cuts such as "plunge cuts" and

"compound cuts." Raise lower guard by retracting handle and as soon as blade enters the

material, the lower guard must be released. For all other sawing, the lower guard should

operate automatically.

d) Always observe that the lower guard is covering the blade before placing saw down on

bench or floor.An unprotected, coasting blade will cause the saw to walk backwards,

cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch

is released.

Before using the circular saw

• Check the following points:

• Does the voltage of the motor correspond with the mains voltage (appliances for a

mains voltage of 230 V

• Are the mains lead and the mains plug in a good condition: solid, without any loose

ends or damage;

• Is the saw blade missing any teeth or showing any cracks, it so must be replaced

immediately.

• Make sure the blade is secure.

• Use this circular saw to saw only wood, wood-like products.

• Do not use circular saw blades wich are deformed or damaged.

• Do not use HSS blades.

• Only use blades meeting the required dimensions, as well as data and descriptions;

Never apply any blades of which the thickness is greater than that of the riving knife.

• Do not stop the blade of a circular saw by pressing the blade from the side.

• Check that the blade guard can freely move and fully closes.

• Never lock-up the guard in the open position.

• Never put sideward pressure on the blade. This may cause the blade to break.

• Be careful when cutting wood with knots, nails or cracks in it and/or dirt on it, as these can

cause the blade to get stuck.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm FKS 185 L Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ferm FKS 185 L

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info