36 Ferm
PLANSLIBEMASKINE (1/2
FLADESLIBER)
Numrene i den nedenstående tekst henviser
til illustrationerne på side 2.
For din egen og andres sikkerhed
anbefaler vi at du læser denne
brugsanvisning nøje igennem, før
maskinen tages i brug. Opbevar denne
brugsanvisning og den øvrige
dokumentation ved maskinen.
Indledning
Planslibemaskinen er designet til at størpudse
overflader af træ, plastik og spartelmasse men
også malede overflader.
Indhold
1. Maskindata
2. Sikkerhedsinstruktioner
3. Samling
4. Anvendelse
5. Service & vedligeholdelse
1. MASKINDATA
Tekniske data
Emballagens indhold
1 Planlibemaskine
1 Stykke sandpapir (struktur 80)
1 Støvpose
1 Brugermanual
1 Garantibevis
1 Sikkerhedsinstruktioner
Komponenter
Fig. 1 + 3
1. Afbryderknap
2. Håndtag (bag)
3. Støvpose
4. Papirklemme
5. Papirklemme på håndtag
6. Ventilationsåbning
7. Sandpapir
8. Sandingssål
9. Håndtag (for)
10.Justér hjul
11.Låseknap til afbryder
2. SIKKERHEDS-
FORSKRIFTER
Beskrivelse af symboler
Betegnelse for risiko for personskader,
dødsfald eller beskadigelse af værktøjet
i tilfælde af at du er uopmærksom på
instruktioner i denne manual.
Indikerer farer for elektrisk stød
Skal man bære støvmaske
Brug beskyttelsesbriller og høreværn
Specifikke sikkerhedsinstruktioner
• Kontakt eller indånding af støv som hvivles op
mens der slibes (f.eks. blymalede overflader,
træ og metal), kan være skadeligt for
brugerens samt tilstedeværendes helbred.
Bær altid velegnet udstyr, såsom støvmaske
og støvposer, mens der slibes.
• Check at maskinen ikke står indstillet til “ON”
position, før maskinen tilsluttes strøm.
• Hold altid ledning væk fra maskindele i
bevægelse.
• Når du arbejder med maskinen, skal du altid
holde på den med begge hænder og holde
den på sikker afstand.
• Anvend beskyttelsesbriller, særligt ved slibing
over hovedhøjde.
Maskinen skal øjeblikkeligt slukkes i til fælde af:
• Defekt netstik, netledning eller beskadigelse
af ledning.
• Defekt kontakt.
• Gnistdannelse i kullene eller ringild i
kollektoren.
Volt 230 V~
Frekvens 50 Hz
Indgående strøm 450 W
Værktøjsklasse II
Ubelastet hastighed 8000-12000/min
Vægt 2,8 kg
Lpa (Lydtryksniveau) 80,5 dB(A)
Lpa (Lydkraftsniveau) 91,5 dB(A)
Vibration 7,4 m/s
2
DK
Ferm 05
4. USE
Operation
• Push in the on/off switch (1) to start the
machine.
• By adjusting the adjusting wheel (10) you can
regulate the speed.
• The ventilating apertures (6) on the housing
must remain clear to ensure optimum cooling
of the motor.
• Move the sander over the surface of your
workpiece.
• Let loose the same on/off switch to stop the
machine.
• The on/off switch can be blocked in position
“ON” by pushing the lock-on button (11) on
the side, while you keep pushing the on/off
switch. The machine can be stopped by briefly
pushing the on/off switch again.
Prevent pushing too much on the
machine during sanding. Excessive
sanding pressure does not lead to
increased sanding capacity, but
increases wear of the machine and the
sandpaper.
Grips
The sander is equipped with two grips: a handle
at the front side and one on the back side. Always
hold the sander with both hands on the handles,
so as to gain the best possible control over your
sanding operations. Besides you do not risk to
become in touch with the moving parts.
User tips
• Apply long uniform movements to your sander
to obtain the best possible results.
• The surface quality after sanding is
determined by the selected grain.
5. SERVICE & MAINTENANCE
Make sure that the machine is not live
when carrying out maintenance work on
the motor.
The machines have been designed to operate
over a long period of time with a minimum of
maintenance. Continuous satisfactory operation
depends upon proper machine care and regular
cleaning.
Malfunction
Should the machine fail to function correctly, a
number of possible causes and the appropriate
solutions are given below:
1. The electromotor gets hot
• Clean the ventilating apertures
2. The dust is not extracted
• The dust bag is full / empty the dust bag
3. The abrasive paper is filled with
adhesive/paint or a similar material
• Paint or adhesive is not really dry.
• Some paints stick more to the abrasive paper
than others / clean the abrasive paper at
regular intervals
Repairs and servicing should only be
carried out by a qualified technician or
service firm.
Cleaning
Keep the ventilation slots of the machine clean to
prevent overheating of the engine. Regularly clean
the machine housing with a soft cloth, preferably
after each use. Keep the ventilation slots free from
dust and dirt. If the dirt does not come off use a
soft cloth moistened with soapy water. Never use
solvents such as petrol, alcohol, ammonia water,
etc. These solvents may damage the plastic parts.
Lubrication
The machine requiers no additional lubrication.
Faults
Should a fault occur, e.g. after wear of a part, please
contact the service address on the warranty card. In
the back of this manual you find an exploded view
showing the parts that can be ordered.
Environment
To prevent damage during transport, the appliance
is delivered in a solid packaging which consists
largely of reusable material. Therefore please
make use of options for recycling the packaging.
Faulty and/or discarded electrical or
electronic apparatus have to be collected
at the appropriate recycling locations.
Warranty
The warranty conditions can be found on the
separately enclosed warranty card.
GB
